0
What is the voltage of a circuit that has a current of 0.5 amps and a resistance of 110 ohms?
Wiki User
∙ 12y ago
Assuming this is a DC circuit, use Ohm's Law to find the answer.
Ohm's Law states E = I x R (Voltage = Current x Resistance)
E = 0.5a x 110 ohms
E = 55 volts
A/C requires a more complicated formula and more information in the given question.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the resistance of the circuit if the voltage is 230 volts and the current flowing is 5 amps?
The resistance of the circuit will be 46 ohms
What is the resistance of a circuit that takes a current of 0.5A when the voltage to the circuit is 40v?
The formula you are looking for is Ohms = Volts/Amps. R = E/I.
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
What is the resistance of a circuit with 120V and 10A?
Assuming DC and resistive loads, resistance equals voltage across the load, divided by the current through it. In this case 120/10 or 12 ohms.
8 If the resistance of an electric circuit is 12 ohms and the voltage in the circuit is 60 V the current flowing through the circuit is?
There is a simple equation relating voltage (properly potential difference), current and resistance: V=IR Where V=potential difference, I=current and R=resistance So to answer: I=60/12 I=5
What happens to amps when you increase the resistance of a circuit?
If you don't change the voltage between the ends of the circuit,then higher resistance in the circuit means lower current (amps).
What is the resistance of the circuit if the voltage is 230 volts and the current flowing is 5 amps?
The resistance of the circuit will be 46 ohms
How do you work out the current in a circuit?
we can calculate the current in a commmon electrical circuit by this formulae i.e,I=V\R where i is the current flowing in the conductor, R is resistance , V is the voltage.. THE FORMULA IS CORRECT but the term conductor does not suffice an explanation since a conductor is low in resistance R= resistance not conduction.
What is the resistance in a simple circuit if voltage is 12 volts and current is 3 amps?
Ohm's Law: Resistance = voltage / current, so 12 / 3 = 4 ohms.
What factors determine the voltage induced in a wire?
V = I * R or I = ( V / R ) I = current (amps) V = Voltage R = Resistance The current in a circuit depends on the applied voltage and the resistance of the circuit.
How many amps will a 260 ohms resistor on a 120 volt circuit use?
Just use Ohm's Law Voltage = Current x Resistance Amps = Voltage Divided By Resistance Amps = 120 / 260
What voltage is required to sustain a current of 0.50 through a light bulb resistance of 190?
The voltage of a circuit with a resistance of 250 ohms and a current of 0.95 amps is 237.5 volts. Ohms's law: Voltage = Current times Resistance
What is the resistance of a circuit that takes a current of 0.5A when the voltage to the circuit is 40v?
The formula you are looking for is Ohms = Volts/Amps. R = E/I.
How much current in amps flows through a circuit with a 100 resistance?
You don't have enough information in your question, you need to include the voltage as well. One relevant equation is V = I * R where V: Voltage, I: Amps, and R: Resistance. When you have the voltage divide the Ohm resistance into that and you'll get your amps.
How do you work out amps in an electrical circuit?
Current symbol I =voltage/resesistance I=V/R for direct current (dc) and for a resistive load in alternating current (ac)
In the electrical circuit the higher the voltage the lower the?
Amps Ohm's law states the current is directly proportional to the applied emf (voltage) and inversely proportional to the resistance of the circuit.
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
