answersLogoWhite

0

Yes, an oil well can be "shut off" by the use of a device that has a hydraulic ram that can crush and seal a pipe (or simply shut a valve) to secure a wellhead. The so-called "blowout preventer" is such a device, but in the case of the current disaster in the Gulf of Mexico, the device failed (owing to a failure to replace a battery, as one report had it).

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

How can I stop a leaky water pipe in my crawlspace?

1. Replace the pipe, 2. Shut off the water


What is casing pipe?

it is defined as the pipe cemented in the well to seal off formation fluids and to keep the hole from caving in.


Where are shut-off valves?

In every home thee are a number of shut-off valves. Where the water pipe enters the house is the main shut off, usually beside the PRV, a bell shaped device for regulating the house pressure. This main cold line will then branch off to the water heater, bathrooms and kitchen. Each faucet and the water heater and the toilet will have a shut-off valve. The hot water line comes out of the top of the heater and goes to bathrooms and kitchen. Each hot faucet also has a shut-off valve under it.


What is causing low water pressure in house and pump to constantly buzz in a deep well?

I do not know your situation but a good guess is that your well pump is always on and is not getting enough pressure to shut off the pressure switch. So I would shut off the power to your well pump and see if the buzzing stops and if it does then I would replace your well pump. If the buzzing don't stop with pump shut off then it could still be your well pump check valve slowly leaking threw but I think its your pump because its not pumping enough to shut off with or with out a bad check valve.


How do you tap into main water line for sprinkler?

Locate your main water line inside house and shut the water off. Cut pipe and place a tee solder into place. Run your line to exterior of house placing a shut off inside.. Test for leaks..

Related Questions

How shut off valves work?

the pipe is closed by a gate or ball that cuts off flow through the pipe


What would you use to solder a shut off valve on to a copper pipe?

What to use to solder a shut off valve


Where is Valve Shut Off on gas water heat?

On any water heater, the shut off is on the incoming cold pipe.


How can I stop a leaky water pipe in my crawlspace?

1. Replace the pipe, 2. Shut off the water


How do you install a shut off valve on an unthreaded pipe?

By soldering or brazing


How can I properly install a shut off valve on a copper pipe?

To properly install a shut off valve on a copper pipe, follow these steps: Turn off the water supply to the pipe. Use a tubing cutter to cut the copper pipe where you want to install the valve. Clean the cut ends of the pipe with a pipe cleaning brush. Slide a compression nut and ferrule onto each end of the cut pipe. Insert the shut off valve between the two cut ends of the pipe. Tighten the compression nuts onto the valve and the pipe ends using a wrench. Turn on the water supply and check for leaks. Make sure to follow all safety precautions and local plumbing codes when installing the shut off valve.


How do you replace an outdoor faucet?

Shut of the water to the faucet. If a local shut off is not present then the main house shut off will have to be used, or the cutoff at the meter. unless plastic pipe is used then the faucet screws onto the water pipe. It will probably take a pipe wrench on the pipe and the faucet to break it free. use Teflon tape to cover the pipe threads before screwing on the new faucet. Turn the water back on and check for leaks.


How is water suspended in cities?

By a shut off valve connecting it to the main pipe to your apartment or house.


What is emergency shut off button in science class for?

It is probably for when there's a gas leak. The room could go up in flames if there's gas everywhere and it is ignited. The emergency shut off will shut off the gas in case the knobs or a pipe is broken


How do you install a shut off valve?

To install a shut off valve, first turn off the water supply to the area where you will be working. Cut the pipe where you want to install the valve using a pipe cutter. Clean the ends of the pipe and the valve with sandpaper. Apply flux to the pipe and valve, then solder them together using a torch. Allow the joint to cool, then turn the water supply back on to test the valve for leaks.


What would cause the kitchen faucet to stop running water?

Someone may have shut off the water to that faucet, or a pipe may have froze, or there may be air in the pipe.


Can vinegar be used on stuck water shut off valve?

You should pour bleach down the pipe.