0
What else can I help you with?
What is a cable gland?
A cable gland is a connector which holds the end of a cable in place.
What will happens to current when cable length increases?
With a constant voltage and increase in wire length will increase the end to end resistance and therefore the current will decrease.
Are power cable armour to be earthed at both ends or at one end only?
One end only. Single point grounding is a rule of thumb. The reason for this is when you run cables together, including a shield or ground cable, the cables with power flowing in them will induce a voltage on the other cables. If two grounds are placed on a shield or ground cable, unwanted current will flow in a loop through the cable.
What is the difference between sheathed and non-sheathed cable?
Cable sheath current is a current induced in the sheath by radio, magnetic or other interference, or a fault condition. The cable sheath should be grounded at one end so that this current flows to ground safely.
How do you make a phone cable terminated RJ45 on one end and RJ11 on the other?
terminate the RJ11 end and on the RJ45 end crimp the 4 wires in the 4 middle slots. run the wires straight through, no crossover
What is a gland in cable?
A gland in cable, commonly called a cable gland, is a mechanical device used to secure the end of a cable to an enclosure, panel, or equipment. It provides strain relief, sealing, and environmental protection for the cable, ensuring safe and reliable performance.
Why cable glands are used?
In the electrical trade devices that are used to support a cable or conduit entry into an electrical device are called connectors. These can be called strain relief,sealtite, EMT, or BX but they are all called connectors When the word gland is used it usually refers to the wiring of explosion proof devices. When making a wire end, the conductors are fed through an empty gland that is twisted on to the end of the explosion proof cable. Into this empty gland is poured a epoxy type compound that hardens itself around the conductors. The hub of the fitting slides over the gland and is screwed into the threaded hole of the device that connects to the cable. By sealing the cable in this method, explosive gasses or dust that might seep into the electrical device is prevented.Pyrotenax, a mineral insulated cable, is one type of cable that uses this method of sealing its cable ends. These type of wire ends are also used with Tech cable that are used in explosion proof areas.
How does patch cable or patch cord work?
A patch cable or patch cord connects one electronic devise to another. By using a patch cable, or patch cord, works by inserting one end into one device, and the other end into another. The wires in the cord will connect the two devices.
Which cable connects directly to two PC's?
A cross-over cable directly connects two PC's without the need for a device such as a switch. The cross-over cable works by having one end's pins in a standard order and the other end swaps the transmit and receive wires. RJ-45 UTP CABLE IS ACTUALLY USED.
Which cable diagram displays the end to end pinout for a crossover cable used with Cisco devices?
Cable C
What is straight cable connection?
All of the pins on one end of the cable connect to the same pin numbers on the other end of the cable, hence, the wire goes "straight through" from one end of the cable to the other.For example, pin 1 on one end of the cable is connected to pin 1 on the other end of the cable, etc.
How do you open the hood of a 2002 Saturn Vue if the hood cable is broken?
Our 2004 Saturn Vue hood release can be opened (if the cable is not broken) by disconnecting the cable from the back of the release lever, grabbing the ball on the end of the cable with some large pliers ("channel locks") and pulling hard. A metal "wire keeper" bracket clamped to the cable end under the hood to serve as a spacer and the release lever works.
How do you properly install brake cable end crimps on a bicycle brake cable?
To properly install brake cable end crimps on a bicycle brake cable, follow these steps: Cut the cable to the desired length using cable cutters. Slide the crimp onto the end of the cable. Use a cable cutter or pliers to crimp the end of the cable securely. Make sure the crimp is tight and secure to prevent fraying of the cable.
What is a cable gland?
A cable gland is a connector which holds the end of a cable in place.
How do you open the hood on a 1986 S10 Blazer when the release cable breaks?
Take a flat screw driver and use it to push the spring away from the hood latch. Locate the screw driver at the end of the cable. This works for mine.
What is the name of the device that should be attached at the end of a cable in a cable topology?
its called a cable
What is the proper way to replace a brake cable end on a bicycle?
To replace a brake cable end on a bicycle, first, loosen the brake cable at the brake caliper. Then, remove the old cable end by cutting it off. Next, thread the new cable end onto the brake cable and crimp it securely in place. Finally, reattach the brake cable to the brake caliper and adjust the tension as needed.
