0
You can't convert kV (kilovolts) to current (amps) unless you know the resistance (ohms) of the load which is taking current from that voltage source.
Once you know the resistance then you can use Ohm's Law to get the amperage:
I = V / R
In words, Ohm's law is:
Current (amps) equals voltage divided by resistance (ohms)
What else can I help you with?
Can the impulse withstand voltage be affected by altitude?
Yes. The IEC 60071.1 Std states a diminish withstand of aprox of 1% every 100mts above 1000mts. For example: for a 13.8kV system the insulation level should be of 95kV (interior). If the installation is going to be at 1,500mts then de minimum insulation level of your equipment must be: 95kv/(1-0.01*(500/100)) = 100kV BIL. The next std value for BIL is 125kV.
How do you convert micro amps to amps?
To convert microamps to amps, you need to divide the value in microamps by 1,000,000. This is because one microamp is equal to one millionth of an amp. So, if you have a current of 500 μA (microamps), you would divide 500 by 1,000,000 to get 0.0005 amps.
What is lighting impulse test on disconnector?
Lightning Impulse withstand test is a destructive test carried out on high voltage switchgear. It is classed as a destructive test as each shot damages the insulation and lays carbon tracks. The Energy Networks Association Technical Specification (ENA-TS) 41-36 states the BIL (basic Impulse level) Required for the Voltage rating of the piece of switchgear rated up to 36kV. For example an 11kV switchgear will have a BIL of 95kV. Switchgear which include a Vacuum circuit breaker must have a second means of isolation, ie a disconnector. This disconnector can be a two position (mains on, off) or three position (mains on, off, or earth on) disconnector operated off load which is in series with the Circuit breaker. To pass the test 15 shots at +95kV and 15 shots at -95kV are fired at all positions of the disconnector and only 2 out of the 15 (and not the last 5) shots can flash over to earth. For example if the disconnector was in the off position one side will be connected to the impulse generator and the other side will be earthed. Positive and Negative shots will be fired and the impulse can not flash through the air gap to the earthed side of the disconnector. This proves the isolation gap inside the disconnector has a BIL rating of 95kV. Therefore if the incoming side of a switchboard is live and the outgoing side is isolated for maintenance. There can be a transient impulse on the live side of the circuit and it will not flash across the isolating gap and endanger anyone working on the dead side of the circuit
How many watts in a 115 volt refrigerator?
How many Amps is the fridge pulling? Multiply the Amps by the 120V circuit you're plugging into and you'll get your Watts.
How do you convert watts into amperes?
To convert watts into amperes you divide the circuit voltage into the watts. Amps = Watts/Volts. <<>> Converting Watts to Amps The conversion of Watts to Amps is governed by the equation Amps = Watts/Volts For example 12 watts/12 volts = 1 amp Converting Amps to Watts The conversion of Amps to Watts is governed by the equation Watts = Amps x Volts For example 1 amp * 110 volts = 110 watts Converting Watts to Volts The conversion of Watts to Volts is governed by the equation Volts = Watts/Amps For example 100 watts/10 amps = 10 volts Converting Volts to Watts The conversion of Volts to Watts is governed by the equation Watts = Amps x Volts For example 1.5 amps * 12 volts = 18 watts Converting Volts to Amps at fixed wattage The conversion of Volts to Amps is governed by the equations Amps = Watts/Volts For example 120 watts/110 volts = 1.09 amps Converting Amps to Volts at fixed wattage The conversion of Amps to Volts is governed by the equation Volts = Watts/Amps For Example, 48 watts / 12 Amps = 4 Volts Explanation Amps are how many electrons flow past a certain point per second. Volts is a measure of how much force that each electron is under. Think of water in a hose. A gallon a minute (think amps) just dribbles out if it is under low pressure (think low voltage). But if you restrict the end of the hose, letting the pressure build up, the water can have more power (like watts), even though it is still only one gallon a minute. In fact the power can grow enormous as the pressure builds, to the point that a water knife can cut a sheet of glass. In the same manner as the voltage is increased a small amount of current can turn into a lot of watts.
Can the impulse withstand voltage be affected by altitude?
Yes. The IEC 60071.1 Std states a diminish withstand of aprox of 1% every 100mts above 1000mts. For example: for a 13.8kV system the insulation level should be of 95kV (interior). If the installation is going to be at 1,500mts then de minimum insulation level of your equipment must be: 95kv/(1-0.01*(500/100)) = 100kV BIL. The next std value for BIL is 125kV.
How many amps are in 40 volt amps?
Multiply the vots by the amps to find the volt-amps. Or divide the volt-amps by the voltage to find the amps.
What does 0.35897amps equals to in amps?
0.35897 amps = 0.35897 amps.
200ma in amps?
200ma is .200 amps or .2 amps
Is the current measured in amps the same as the keyword "amps"?
Yes, the current measured in amps is the same as the keyword "amps."
What is the difference between 5 amps and 12 amps?
7 amps
How many amps are there in 20 Mega amps?
There are 20 million amps or 20,000,000 amps.
Convert 18 VDC to AC amps?
Amps is amps be it DC or AC.
How many amps gives you 0.1amps?
.1 amps will give you .1 amps.
What does 24vac 50va equal to in amps?
In 50 VA the V stands for volts and the A is for amps. Hence the formula you are looking for is 50/240 = Amps.
generator amps?
What is the generator amps
How do you convert HV amps to LV amps?
To convert high voltage (HV) amps to low voltage (LV) amps, you can use the formula: HV amps = LV amps x (LV voltage / HV voltage). By rearranging the formula, you can calculate LV amps by dividing HV amps by the ratio of HV voltage to LV voltage.
