0
What else can I help you with?
What is the Float adjustment for 087A keihin carb for a 550 Honda motorcycle?
22mm is the float height for this carb
Where is the part number on a keihin carburetor?
The part number on a Keihin carburetor is typically found on the side of the carburetor body or on the underside of the float bowl. It may be stamped or printed, and can often include a combination of letters and numbers. If you can’t locate it easily, consulting the specific model’s service manual may provide more detailed guidance.
Where is the float boat located on a Kawasaki Ninja 500 and how do you drain the carburetors?
Do you mean float bowl,and they are on the bottom of the carbs.To drain them you'll need a special tool(looks like a long Allen wrench,about 2 foot in length)and there is a drain screw on each of the carbs.AnswerI used to drain mine with a flat head screw driver, it has to be long, but not 2 feet. Just make sure the engine in cold, you can see the drain screws on the carbs. Just get a Clymer Manual and it will tell you everything you need to know. I also believe that the screws are both accessed from the right hand side of the motorcycle.
How do you install a fuel float?
To install a fuel float, first ensure the fuel tank is empty and clean. Remove the old float if applicable, then insert the new fuel float into the designated opening, making sure it aligns properly with the float arm. Secure it in place, typically with screws or clips, and reconnect any electrical connections. Finally, test the float's functionality before refilling the tank.
How do you adj the float on a 93 400 bayou?
The float on a 1993 Bayou is tricky to adjust. You first have to remove the carburetor from the quad, Remove the four phillips screws that hold the float bowl cover on, take a small screwdriver and bend the float upwards or downward depending on whether you want more or less fuel.
How do you drain a fuel from a larson lxi 190?
Remove the access plate from under the rear bench (round with about 6 screws). Underneath you will be able to seen the fuel tank and fuel gauge float port. Unscrew the screws holding on the fuel gauge float. Gently remove the fuel gauge float. Insert long syphon tube into tank and run hose either over the side or through drain port to the outside and into holding tank.
What causes your engine to sputter at high rpm on your dirt bike?
it can either be the coil that provides the spark for the spark plug failing or an out of tune carburator. i would try cleaning the carb but being very careful not to move the screws/float bowl position/ or air screw. but spray everything with carb cleaner and spray dry with an air compressor, making sure all needles are cleaned out with thin wire. nathaniel. work at goodyear and recently was taught by lead mechanic how to clean carbs and fixed my motorcycle just yesterday from cleaning the carbs extensively and tuning.
How can you adjust the carburetor float on a 1987 ford clubwagan van which has a holly 4bl carburetor.?
don't do it unless you know how and if you did you wouldn't be asking adjusting carbs is an art form so I sugest you find an old mechanic ie; someone in ther fifties they are about the only guys left that know how to adjusat carbs
Where is the float on a VW Beetle carburetor?
inside it- remove the air filter from above, and there will be five screws (flat head type) on the top of the carb. undo those, and lift the top of the carb off. the float chamber is the bit furthest away from you, and the float is the (usually) brown plastic, hopefully air filled, box.
How do you fix a stuck carb needle on a Yamaha Warrior 350 when the screws on the float bowl are stripped?
Remove them with some WD-40 and some vice grips.
Yamaha exciter 570 snowmobile starts then stalls then its flooded why?
take off the carbs and clean them out with come carb cleaner. Might be the choke cable sticking, or float bowls level is too high
How do you change the main jet on a VLX 600 carburetor?
Depends on what year the bike is. Well not really, just that earlier years had two carbs meaning twice the work. Most all carbs have screw-in jets. Just remove the carb (fuel hoses and throttle cable linkage), then the float bowl (the bottom of the carb body) and the jets are there for the removing.
