Use an oscilloscope. That shows the voltage waveform and you can read the peak value.
2x the peak supply voltage!
RMS stands for "Root of the Means Squared", and is a mathematical method of defining the "operating" voltage of a sine wave power source. Typical home lighting and outlet voltage presently is 120 VAC (volts alternating current), 60 Hz. (Hertz, formerly referred to as "cycles per second".) But the PEAK voltage is the absolute maximum voltage at the "peak" of each sine wave of voltage. Mathematically, the "Peak" voltage is 1.414 (which is the square root of the number 2) times the RMS voltage, and conversely, the RMS voltage is 0.707 times the PEAK voltage.
A: Take 115 volts and multiply by 2.82. The frequency does not matter but he voltage does
You mean peak inverse voltage.It is the maximum voltage (peak) the diode can be reversed biased (inverse) by without being destroyed.
RMS and peak voltage for a square waveform are the same. There is a small caveat, and that is that you'd have to have a "perfect" square wave with a rise time of zero. Let's have a look. If we have a perfect square wave, it has a positive peak and a negative peak (naturally). And if the transition from one peak to the other can be made in zero time, then the voltage of the waveform will always be at the positive or the negative peak. That means it will always be at its maximum, and the effective value (which is what RMS or root mean square is - it's the DC equivalent or the "area under the curve of the waveform") will be exactly what the peak value is. It's a slam dunk. If we have a (perfect) square wave of 100 volts peak, it will always be at positive or negative 100 volts. As RMS is the DC equivalent, or is the "heating value for a purely resistive load" on the voltage source, the voltage will always be 100 volts (either + or -), and the resistive load will always be driven by 100 volts. Piece of cake.
Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.
You measure the peak to peak voltage and divide by 2.
Simply multiply the peak voltage to 2 and you will get the peak to peak voltage.
ANSWER: The peak to peak voltage can be found by multiplying 120 v AC x 2.82= 339.41
A: Peak voltage is RMS multiplied by a factor of 1.41
Another name for average voltage is the RMS (Root Mean Square). This is a voltage derived from the peak to peak voltage multiplied by .707. If the peak to peak voltage is 170 volts then the average voltage (RMS) would be 170 x .707 = 120 volts.
The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.
It is the highest value of the amplitude, called the peak value. Scroll down to related links and look at "RMS voltage, peak voltage and peak-to-peak voltage". Look at the figure in the middle below the headline "RMS voltage, peak voltage and peak-to-peak voltage".
When the peak voltage is 311, the RMS voltage is 220. (311 * square root (2))
No, the peak-to-peak voltage is 2sqrt(2) times as much as the rms for a pure sine-wave.
If you are referring to the voltage after the rectifiers in a powersupply, it is due to the voltage drop across the rectifiers.
What are the Importance of of peak inverse voltage in rectifier