0
Base load is the level that it typically does not go below, that is, the basic amount of electricity that is always required.
Peak load is the daily fluctuation of electricity use. It is usually lowest in the wee hours of the morning and highest in the early evening. It also varies seasonally.
Are base and peak loads provided differently?Base load is typically provided by large coal-fired and nuclear power stations. They may take days to fire up, and their output does not vary.Peak load, the variable part of the electrical supply and demand, is provided by more responsive and smaller plants whose output can be quickly ramped up and down or that can even be quickly turned on and off.
What else can I help you with?
What is the difference between prudential and moral reasons for power sharing?
Prudential reason stress that power sharing will bring out better outcomes, whereas moral reasons emphasis the very act of power sharing as valuable.
What is meaning of lv leads hv with 30 degree?
"LV leads HV with 30 degrees" typically refers to the phase relationship between low voltage (LV) and high voltage (HV) electrical systems. In this context, it indicates that the voltage of the LV system is leading the HV system by 30 degrees in terms of phase angle. This phase difference is important in power systems to ensure proper synchronization and efficient operation of electrical equipment. Overall, it highlights the timing difference between the two voltage levels in an electrical circuit.
How do you measure the power by 3 voltmeter method?
first we connect the 3 volt meter in three loads then we measure the voltage and find the resistance of the loads then put the formula p=v/r so in this method we get the power by using 3 volt meter ....(prashant)
What is the difference between a nuclear power station and coal fired power station?
The difference is in the name; nuclear power plants produce electricity via a nuclear reaction producing head to turn a turbine, whereas coal fired power plants burn coal to produce the same efffect.
What was a foundational difference between Stalin and American political leaders?
A foundational difference between Stalin and American political leaders lies in their governance styles and ideologies. Stalin's regime was characterized by totalitarianism, centralized control, and the suppression of dissent, prioritizing state power over individual rights. In contrast, American political leaders typically emphasize democratic principles, individual freedoms, and a system of checks and balances designed to prevent the concentration of power. This fundamental divergence reflects their differing views on the role of the state versus the rights of the individual in society.
What is the difference between a brake booster and power brakes?
The brake booster is part of the power brake system.
What is included in an indoor plant system?
An indoor plant system includes: AC power system (input switch gear, standby plant, distribution system, and backup systems for uninterruptible loads and protective loads) and DC power system.
What are the differences between capacitive and inductive loads and how do they affect the performance of electrical systems?
Capacitive loads store and release electrical energy, while inductive loads resist changes in current flow. Capacitive loads can lead to power factor issues and voltage fluctuations, while inductive loads can cause voltage drops and power losses. Balancing these loads is important for efficient electrical system performance.
What is difference between feeder and grid?
In an electrical power transmission system: the grid is what the feeder feed into.
What the difference between process piping and power piping?
What the difference between process piping and power piping?
What is the difference between a run and a circuit?
run in a electrical system means a wiring & conduit runs coming from Panel Board Circuit Breaker to its branch circuit loads in a circuit. while circuit is a designated number of branch breaker in a panel board where power load was individual connected.
What are the key components and functions of a DC bus system in an electrical power distribution network?
The key components of a DC bus system in an electrical power distribution network include a power source, a busbar, circuit breakers, and loads. The functions of a DC bus system are to distribute power from the source to the loads, regulate voltage levels, and provide a stable power supply to the connected devices.
What is the difference between a strong-mayor system and a weak-mayor system?
in the strong-mayor system the mayor has strong executive power, and the weak-mayor system the mayors authority is limited
What is the difference between a strong-mayor and a weak-mayor system?
in the strong-mayor system the mayor has strong executive power, and the weak-mayor system the mayors authority is limited
What is the difference between a strong and weak mayor?
in the strong-mayor system the mayor has strong executive power, and the weak-mayor system the mayors authority is limited
How much coolant is needed in a nuclear power station?
loads and loads and loads and loads
What is the difference between the parliamentary system and the American congressional system?
In a congressional system the President holds a lot of power, hence the name executive branch. In a parliamentary system the power is spread wider out and one person does not have absolute power. In a parliamentary system there is a wider representation of people, more representatives, and many different positions.
