0
What are the torque settings for valve cover gasket screws on a 1997 Jeep Grand Cherokee Ltd 5.2 L V8?
Wiki User
∙ 15y ago
Torque settings are 110 ft LBS for nine of the ten bolts one bolt is 100 ft LBS /#1 Tighten all bolts in sequence 1 to 10 at 22 ft LBS #2 tighten all bolts 1 to 10 at 45 ft LBS #3 tighten all bolts 1 to 6 at 110 ft LBS #4 bolt #7 at 100 ft LBS #5 BOLT 8 TO 10 AT 110 FT LBS . HEAD TIGHTEN SEQUENCE - standing at front of car bolts down left side are 8/4/1/5/9 bolts down right side are 7/3/2/6/10. left side meaning distributor side. A four cylinder engine has ten (10) bolts. A six cylinder has fourteen (14) bolts.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
When replacing the valve cover gasket on a 2004 jeep grand Cherokee limited- 6-cylinder 4.0L what is the correct torque or sequence for tightening the screws on the valve cover?
The correct torque spec is 85 INCH lbs.
Will a 97' Grand Cherokee torque converter fit a 93?
No.
What is the front wheel bearing torque spec for 1996 grand Cherokee?
It is 175 ft lbs for the front wheel bearing of a grand cherokee
How much torque does the engine in the 2014 Jeep Cherokee have?
The 2014 Jeep Cherokee's engine produces 171 ft-lbs. @ 4800 rpm.
Jeep Cherokee torque specs front axel carrier bolts?
60ft/lbs
What are the torque settings for the heads on opel kadett 1993 model?
The torque settings are normally included on a sheet when buying the gasket set.
When replacing the valve cover gasket on a 2004 jeep grand Cherokee limited- 6-cylinder 4.0L what is the correct torque or sequence for tightening the screws on the valve cover?
The correct torque spec is 85 INCH lbs.
Cylinder head torque settings for Volvo fl6?
Torque settings for FL6 Volvo
What is the torque settings for valve cover screws on a 2000 Jeep Grand Cherokee with a 4.0 engine?
Should be 10 in.lbs. I believe this would be 10 ft lb not inch lb
Harley 883 torque setting?
Torque settings for the 11 screws that secure the transmission cover on an 08 sportster
Torque wrench settings for head gasket diesel 2h Toyota landcruiser?
113nm mate
What are the torque settings for a vauxhall astra mk4 cylinder head?
when u buy a head gasket for the car usually the toque settings or on a piece of paper in the packet
What are the tie rod ends torque bolt settings on a 2000 Jeep Grand Cherokee Laredo FWD?
The tie rod torque bolt settings, on your 2000 Jeep grand Cherokee, is 70 pounds per square inch. The bolts should be torqued in 35 pound intervals.
How do you Run in a head gasket?
to RUN in a head gasket,u torque the head bolts to specs.you then run engine for specified amount of time, then again torque head bolts to specs. most shop manuels will give you 2 toque settings.
What are the cylinder head bolt torque settings on a 2001 Jeep Cherokee 3.7L V6 engine?
The 2001 Jeep Cherokee 3.7 liter engine cylinder had bolt torque specification is 150 pounds. The cylinder head bolts should be torqued in 50 pound intervals.
Torque settings for megane 1600 k4m?
torque settings for cylinder head bolts
What are the torque specifications for a Subaru Outback 2.0 TD engine?
You need to specify which torque settings. As with any vehicle, torque settings are specific to a particular part of the vehicle.The torque settings for the cylinder head will differ from the settings for the crankshaft bearings.
