This idea is not economic.
It would cost more to convert it safely than buying one or more single phase heaters (either second-hand or new) to give the same heating effect.
3-phase heaters are not usually intended for domestic use in homes, except for the latest new-builds which have 3-phase supplies. They are commonly used in industrial sites (factories, workshops, etc.) or large public areas (department stores, airline terminals, etc.) where a 3-phase power supply would be installed as standard at the site.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
One common method to convert single phase to three phase power is by using a rotary phase converter. The rotary phase converter works by using a single-phase power source to generate a third phase, creating a balanced three-phase output. It typically involves using capacitors and an electric motor to create the additional phase needed for three-phase equipment.
To calculate the amperage for a 10kW heater on a 3-phase 220V system, use the formula: Amps = (kW x 1000) / (√3 x Volts). So, Amps = (10 x 1000) / (√3 x 220) = 26.18 amps per phase. Therefore, the total current drawn by the heater is 26.18 amps per phase multiplied by 3, which equals approximately 78.54 amps.
No, a single-phase supply cannot be directly used in a three-phase system. The voltages and phases are different, so additional equipment such as a phase converter or transformer would be needed to convert the single-phase supply to match the requirements of the three-phase system.
In a three phase that means there are three lines live. Lets name the first line L1, second one L2 and the last L3. If you would connet it to a three phase motor then you require L1, L2 and L3 to be connected either in star or delta connection. Rating of your motor should be 200V, 3 phase , x HP ( star or delta connected). If you have a single motor of 200V then you only need to connect two lines of the three., namely either L1 to L2 , L1 to L3 or L2 to L3.
For a three-phase, four-wire, system, single-phase loads can be connected between any pair of line conductors. For a three-phase, four-wire, system, single-phase loads can be connected between any pair of line conductors, or between any line conductor and the neutral conductor. The choice depends on the voltage requirements of the load.
The power is generated in the form of three-phase in aircraft, and this sytem has no problem in feeding single phase loads. To conserve mass in tansformers and motors the supply works at 400 Hz.
Rephrase your question so that it makes sense.
Its a servo.
Single phase can't be turned into 3-phase by any reasonable means. But on the other hand resistance heating is fairly straight forward. If only the fuse rating is high enough it might be possible to rewire a 3-phase heater to run from a single-phase source.
Most electrical equipment are either designed to work on Single phase (two wires) or Three Phase (three or four wires). Two phase equipment are non existent today. A single phase heater will require a single phase thermostat while a three phase heater will require a three phase thermostat.
no
By having a transformer with 3 phase input and single phase out put
I dont know if you can actually convert the oven's wiring from 3-phase to single phase. You can, however, convert the single phase circuit that will feed the oven to a 3-phase system. To this you will need a phase converter. Now, where to purchase such an item, and how much they cost? i have no idea.
No, it is not possible to convert a 2.4 kw single phase appliance to a 9kw 3 phase appliance. Single phase can not be converted to three phase with out considerable cost involved.
Starting capacitors are only required for single-phase induction motors. They are not necessary for three-phase motors.
Houses generally run on single phase power. It would not make sense to convert single phase to three phase to run a house. Please restate the question.
Yes of course!! 10 kva electrical power is 10 kva electrical power either it would be three phase or single phase. But other factors i.e. current, voltage changes accordingly. Actually this question is quit confusable. Because in 3phase system, if each phase gives 10kva power (single phase power = 10 kva) then 3 phase power will be 10 X 3 = 30 Kva If we go leteratualy towasrds the question, then the asnwer will be - No. becasue 10 kva supply to 3 phase load will be 3phase supply(i.e440V) & 10kva supply to single phase load will be single supply (i.e 250V).