0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
How do you set timing on a small block Chevy with a performance cam?
Start at 6 degrees advance, (BTDC) and go up from there until the motor pings, under load. Then back off a couple of degrees. That is called power timing it. You will probably end upabout 10 degrees, advanced. If it cranks over hard, when hot, back it off a couple of degrees.
What type of engine oil for a 2003 Chevy 2500?
sometimes it's mentioned on the dipstick or on a sticker underneath the hood
Can be normal if it happens at a traffic light and again once you get moving again. Might still have some air left in the cooling system. Sometimes tricky to get it all out. Just taking the cap off the tank and running it for sometime will help, often times just drive it with eventually get rid of the air.
Hopefully it's not a leaking head gasket!
How do you bleed brakes on a 2000 Chevy 1500?
you can gravity bleed by opening up bleed valves,pump them up using a someone to open bleeder valves when there is pressure,vacuum bleed with a vacuum pump ,but you might have to use a scan tool to open up abs solenoids to bleed brakes.
1987 Chevy pickup 4x4 When in two wheel drive should the hubs be locked or free?
they should be free, when in 4x4 they should be locked.
change pick up coil in distributor check the triangular points on the round part that triggers the pick up coil corrosion and degrading material common problem requires distributor removal and disassembly of the distributor
Which rapper sing the song my Chevy sit so high from the floor?
Tay Dizm Feat. T-Pain Rick Ross - Beam Me Up
What was the first year Chevy come out with vortec engines?
The name first appeared in 1988 on a 4.3 L
1996 in full size trucks.
Where is the solenoid on a Chevy Equinox?
On top of the starter? Follow the + battery cable should connect to the solenoid
Were is the wiper delay module located on a 97 Chevy pickup?
the wiper delay dodule is located under the hood on the firewall. you will see the motor for the wipers and you take that cover off. it has 3 torx bit screws that holds it on. under this cover is a circut board. that is your wiper delay module.
One of these boats is Chevy Toy, a 142-foot custom-designed yacht. The gleaming white vessel has three decks, including one with a "sky lounge" that has views on three sides, jet skis, and two Vespa scooters on hand for speedy onshore excursions. Its owner is Gene Reed, who made his fortune building and eventually selling a string of Chevrolet dealerships in the southern United States. Mr. Reed's tastes mirror new megayacht owners these days, as does his choice of builder: Trinity Yachts, of New Orleans. "I made my money in the U.S. and I want to spend it here," says Mr. Reed, who paid roughly $20 million for Chevy Toy:
Spark plug gap 292 Chevy 6cly 1950 Chevy?
i'd put them at around .03-.04 gaps on them. that's a pretty general spark plug gap.
What is the angle of the intake valve on a big block Chevy?
26° relative to bore centerline and then 4° relative to crank centerline.
Exhaust is 17° and also 4°.
The driver side brake and signal light is not working on my 98 Chevy 1500?
most likely a bulb b/c if it was the fuse your other brake and signal light wouldn't work... most vehicles the brake and signal light are all in one bulb... try replacing the light bulb
How do you replace windshield washer motor 1998 Chevy truck?
... I am wondering the same thing. I need to replace mine in a '96. ... I am wondering the same thing. I need to replace mine in a '96.
How do you remove door panels in a 57 Chevy?
To remove door panels (front or rear on a 4 door), open the door.
Remove (unscrew) the door lock button
Remove the inside window frame (garnish) by removing all of the screws, then
pull the upper portion out toward you and lift
Remove the two large Phillips head screws holding the arm rest on the door and
remove the armrest
Remove the two large Phillips head screws holding the arm rest holder on the door
Remove the arm rest holder
Remove all screws from around the edge of the door panel
Using a special "forked" tool, slide the tool between the door handle and the white
plastic washer and force the snap ring out of its seat. Remove the door handle
being careful not to lose the snap ring (you can clip in back into the door handle
and leave it there at this point
Repeat the above process with the vent window crank and the main window crank
(If appropriate)
Gently pull the door panel loose on the top and the sides. Grasp the panel and
gently lift up and out of the track on the bottom of the panel
Reverse the process to reinstall the panel.
