Chevrolet

how to replace a knock sensor on a 2000 Chevy 6.0 step by step

A wiring diagram for a starter can be found in Chevy forum websites. It can also be found in the maintenance manuals bought at car shops.

285 horsepower

P0300 Diagnostic Code - Random Misfire

Symptoms.
Engine may stumble or miss
Engine may be hard to start
you may notice no issues

Cause
Failing spark plugs or spark plug wires
Bad coil or coil pack
Failing oxygen sensor(s)
Bad fuel injector or more than one
Stuck exhaust valve
Bad catalytic converter
EGR valve or valve passage clogging
Bad camshaft position sensor
Bad PCM or ECM

The Fix
Best first action is a tune up, new plugs, wires, inspect all hoses and wire connections then reset the code. If it returns you will need to narrow it down to a system, coils and coil packs should be tested, catalytic converters for function ( do you smell rotten eggs?). A misfire that jumps cylinders could indicate a lean condition, do you have any other codes along with the 300? this will help clue you in to the source, check valve function to make sure they are opening and closing fully.
This is probably pone of the most difficult codes to troubleshoot, so start with the basics and work your way into the more expensive options, in many cases a good old tune up solves the problem, back it up with a fuel system cleaning and see where you stand.

to adjust cluch 3 spped trans 1963 c20

The 400 Chevy small block motor should have approximately 390 horse power. It should have 427 foot pounds of torque.

The crankshaft positioning sensor is located on the bottom of the plastic timing chain cover, right behind the crank shaft pully. It is held in place by a metal clip with a single 10mm bolt.

The oil pan is mounted on the bottom of the engine block.

There isn't one. Pull the lower hose.

58.cc low torque swirl chamber head

on driver's side of engine....right above the manifold...about center between the two front spark plugs.

On the driver's side of the engine, between either the front two or middle two spark plugs.

I ground roller cams for Erson, that were up to .650 lift.

Best place is in one of the cylinder heads, by the spark plugs. Or, the intake manifold, near the thermostat housing.

will a 95 chevy k1500 transfer case hook up to a 96 chevy k1500 transmission

Inside the rear of the alternator

the weight of my 427 Chevy big block. Which is the same as the 396, 454.

This is a bare block we are speaking about. the total weight of a bare block Is right at 200 pounds.

bore= 4.125" stroke=3.75" multiply them like this, first get the circular area of the cylinder which is PI *r squared. so, pi (3.14159)x radius squared (half of the bore, squared)(2.0625)x(2.0625)= 13.3640. then multiply that by distance traveled, or stroke, so, 13.3640 x stroke (3.75) x number of cylinders (eight here) (8) = 400.92 cubic inches

my 92 c1500 4.3 is giving me tons of issues I just put new egr throttle position sensor igintion control module plug wires dist and its still bogging down what can the next soulution be even changed fuel filter

the 4.3 L vortec takes 5 quarts of 5W-30 oil also the filter is an acdelco PF61 but just to make sure start the car after putting the oil in run it for a minute then check the dipstick, i always put in 5 quarts

Anywhere from 80, up to 180, depending on ther compression ration, effective compression ratio, and how many miles on the motor. Lower than about 80, is getting low. Also, you are looking for a cylinder that is really low, compared to the rest. 30 lbs., or more, lower. This would indicate a dead cylinder.

5 on 4 and 3/4rs.

Traction Control Not Functioning. When computer senses one wheel losing traction, traction control applies the brake to that wheel to stop it from spinning

Trouble code P1221 means:Throttle position (TP) sensor 1-2 correlation

Around 290hp