0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
How many quarts of oil will a 3.8 engine hold?
A 3.8 liter engine holds up to five quarts of oil. You can start with 4 quarts, start the engine, let it run for 2 minutes, turn it off and wait for another 2 minutes then?æcheck the oil level. You can add more oil if needed.?æ
Is a Chevy 3.1 an interference engine?
No, it is not an interference engine. It also uses a timing chain, not a belt.
What happens if you put gasoline in a diesel?
well what happens is the engine doesn't work no more. Also you will have to replace the fuel pump.
A wiring diagram for a 1974 Chevy 366 big block?
Your going to have trouble with that one. I remember 1974 like yesterday, but not a 366, big, or small block, from Chevy. If you are trying to say 396, again, trouble, as the 396 had morphed into the .030, version of the 402. There was a 348, but that died with the 409, in 63, I think, then there was the......
How do I fix a 1990 Chevy serpentine belt from squealing?
Could be a couple causes for this:
* the tensioner may need replacing - not keeping enough tension on the "S" belt * worn (stretched) serp belt - replace ~ every 50 or 60k miles.
Where is the ECM module located on a 1995 Chevy 1500 pickup?
Take the inside of the glove box out and look in and down to the right just behind the dash and you will see it. It has a 100 wires connected to it.
What cars does a 3.1 multi-port V6 fit into?
I have a 1990 Beretta GTZ that had a 2.3 high output, and it was blown when i got it so i put a 3.1 multiport in it. It works good but it was a ton of work, i even had to change two of the motor mounts. i don't know what else it can fit in but it fits into my car and works!
How do you replace the serpentine belt on a 1993 Chevy c1500?
the belt goes over what's called a tensioner pully that is spring loaded you put a wrench on that and release the tension and the belt is free'd now you put the new belt over the other pully's exactly like the other one (should be a diagram under hood or on the radiator support) and finish by releaving the tension again and putting the new belt around that pully. ps. don't leave the wrench on the truck.
Reset check oil light in 2003 Chevy hd 2500?
Turn key to ON position and then pump the gas pedal and it will reset oil life meter.
How to replace te radio on a Chevrolet Nubira 2006?
Remove the radio retaining cover. Remove the radio retaining bolts. Remove the wiring harness and the cable antenna from the back of the radio. Reverse the process to install the new radio.
How do you replace the ignition switch on a 2005 Chevy Equinox?
how to replace an ignition switch for 2005 chevy equinox
Why would a car continue to sputter after being shut off?
Several things can cause this phenomenon, called dieseling. Built up carbon in the cylinders, incorrect timing, an overheated engine, a lean carburetor setting, or a fast idle can all be contributors to dieseling.?æ
Where is the high beam fuse located in a 1995 Chevy?
The high beam fuse in a 1995 Chevy is located in the fuse box that is under the hood. The box is located on the driver's side fender wall.
Where is number 1 at on a the distributor cap for a 70 Chevy 454?
When the # 1 piston is at TDC on the compression stroke, the rotor is pointing to at the # 1 position on the cap. # 1 cylinder is on driver's side, at front of engine.
How do you replace the ignition switch on your 1993 Chevy K 2500?
Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.
In what order do the spark plugs go onto the distributor cap on a Chevy 5.7 liter?
The order is on the stock intake manifold. It is 1,8,4,3,6,5,7,2
Ac bypass pulley on 1989 Chevy?
An ac bypass pulley for a 1989 Chevrolet can be purchased at any auto parts store. The cost for the pulley starts at $26.04.
Fluid for rear differential Chevrolet 1970 4x4?
You can use any SAE certified rear differential fluid in your 1970 Chevrolet. The 1970 Chevrolet differential fluid can be checked from the differential fluid check port.
How do you replace starter on 1988 Chevy 1500 pickup?
Remove the positive battery cable from your 1988 Chevrolet 1500 pickup truck battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
Best way to add fluid to manual transmission in 1990 Chevy half ton transmission?
Purchase a small inexpensive hand pump and a quart of the correct lube from any auto parts store. My advice is to pay a shop to do it for you and save yourself the hassle.
How do you install a serpentine belt on a 1994 Z71 305 Chevy engine?
Put the serpentine belt on to the pulleys of your 1994 Chevy engine. Tighten a serpentine belt with the tensioner pulley.
