0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
How do you change out a solenoid in a 1997 Chevy 1500 its got a 4L60E transmission?
Starter solenoid?
Dexcool and a Chevrolet 3800 V6?
What was the situation with DexCool and the Chevrolet 3800 series II engine and how do i get the replacement intake manifold from Auto-zone and what is the part #
Yes they are good cars and i saw a Chevrolet Impala with 400000 kilometers
How do you know you have a bent valve in a big block Chevy?
Well, it will pop out the carb, or exhaust, witchever valve is bent. Pull the valve covers off, and turn the motor over slowly, by hand. Make sure all of the valves are closing, or, the stem height is all the same at one point, on every valve. And remember, a burned valve, will act the same as a bent, or stuck valve. A cylinder leakdown test is the proper way to diagnose this, however, that requires a few specialized tools, which most people do not have in their garage.
How do you know you have bent valves in Chevy big block?
Popping out the exhaust, or carb. Engine will run rough on acceleration. Pull the valve covers off, and sping it over by hand, watching to make sure all the valve stem heights are the same, at one point. A rocker arm will have accessive slack, at some point. A cylinder leak down test is the proper way, however, it requires several specialized tools.
On a Chevy 454 Big Block what does the engine code T0625 PPH Stand for?
It means it was built in the Tonawanda, Ny plant on June, 25th. The PPh is the horsepower rating and cubic inch but I don't know exactly which one the PPH is.
Where the distributor on a 1994 Chevy sliverado 1500?
it should be right behind T.B.I unit....just follow your spark plug wires from block to..distributor and there it is....
As long as you take care of them. My 1986 pick up has two hundred and eighty something thousand miles and im still on the motor and tranny is left the factory with.
How many gallons of gas will a 1999 Chevy SS hold?
If you are asking about the Impala it holds 17 gallons.
Where is the low side service port on a 1992 Chevrolet 4x4 truck 305?
Its in the biggest line trace it from your a/c compressor.
What is the value of a 1931 Chevy 5 Window Coupe?
All there in decent shape as a 20-footer is $12,800.
Check the timing.
Engine power reduced light is on in Chevrolet hhr?
The engine power reduced light will turn on in Chevrolet HHR when a failure is detected in one of the sensors or engine components. An OBD II code reader can determine the cause and help with making repairs.
How do you replace a Chevy 4.1 liter engine timing chain?
if it is a 4.1 straight six it has no chain just 2 gears that must be removed with a puller and the new gears must be heated in OIL to slip on and then they tighten as they cool
How do you change rear brakes on a 1994 Chevy CK1500?
Break all rear lug nuts loose. Jack up rear end and put blocks or jack stands under rear end. Now remove all the lug nuts and remove the wheels and tires. Now take a hammer and smack the brake drum to loosen it (not always necessary) now remove drums on both sides. I would recomend leaving one side together while you work on the other side. This way you can use one side for reference if you cant get the other back together.
What is the firing order of a Chevy 4.3 6 cylinder engine?
It should be printed on your intake manifold.
What size engines came in a 1970 Chevy C-10 pickup?
The base engine was a 250 inline 6 cylinder. Also could be ordered with:
292 Inline 6
307 V8
350 V8
396 V8
How do i remove a 79 Chevy c-10 ignition cylinder?
1. disconnect the negative cable at the battery, place the cable out of the way so it cannot accidently come in contact with the negative terminal of the battery, as this would once again allow power into the electrical system of the vehicle. 2. Remove the steering wheel. 3. Place the lock in the run position, remove the lock plate, remove the directional signal switch just far enough to slip it over the end of the shaft without pulling the harness out of the column. Remove the lock retainer screw and the lock cylinder. Note: Be very careful when removing the screw (use a magnet screwdriver, if available). If the retaining screw is dropped during removeable, it could fall into the steering column. The column would have to be completely disassembled to remove the screw. To reinstall: 4. Hold the lock cylinder in your hand and, with the key in, rotate the knob clockwise to the stop. Align the cylinder key with the keyway in the housing and push the lock cylinder all the way in. Install the lock retaining screw and tighten it securely. 5. Install the turn signal switch and the steering wheel.
You have to disconnect the driveshaft and transfer case or front driveshaft. Just remove everything that will turn the transmission.
Where is the Radiator drain on 1996 Chevy 6.5 turbo diesel?
Plug at the bottom of the rad you twist out.
How much horse power does a 4.3 v6 Chevy engine have?
210 hp on some and 190 hp on others depending on the year.
