Computer Networking

Yes, it's possible. Connect the wire coming from the switch in the internet port in the router.

A letter addressing scheme has to do with a TCP/IP protocol. Addresses are determined by both decimal and binary counting.

rahul

Spelling difference.... :)

MSTSC - Microsoft Terminal Services Client

Once your exchange server configuration is done run the

tool EXBPA.exc .This will give you the correct ficture of

your exchange organization.

Thanks

Yogesh

- TheVLANs may be named.
- The network administrator may create the VLANs in either global configuration mode or VLAN database mode.

btrbtrbfdsvdf

Is this a lan or a wan network. Is the client on a different subnet of the network? You could even be talking about a client connected through VPN here... ok, be a bit more specific.

Want to access the client. Would RDP not be the obvious thing..?? You could set the client up to accept incoming connections. You could do a java script that would allow you to just log in and take control of the machine. Be more specific about the network and what sort of access you want.

To get the mac address you will need to use Address Resolution Protocol (ARP). Pretty much this will show an IP address and then give you the MAC address of that computers network card.

As for the user changing it. Obviously you cant prevent a user from spoofing a MAC address, but as far as I am aware you cant change it permenently. So I dont think there is very much to worry about there. Also, unless you are dealing with technically minded people, I would doubt that they would even know how to spoof a MAC never mind change it (if its possible that is - which, like I have already said I really dont think it is)

A virtual channel defines a single point to point connection, identified by its virtual channel identifier (VCI). A virtual path however, is a bundle of virtual channels that share the same end-point. Hence, a virtual path can be considered as a container that contains several virtual channels. Each virtual path is identified by its unique virtual path identifier (VPI). sridhara................

No single figure can be given, as this has varied widely over the years with changing technology (e.g. tube, transistor, IC, VLSI), architectural improvements, implementation (e.g. microcode vs. hardwired logic vs. programmable logic devices), etc.

No.

The POP3 protocol is a network protocol. It is only concerned with the messages sent back and forth between the mail server and the mail client.

The internal format of the mailbox files on the server is only of concern to the POP3 server software. It needs to be able to read the mailbox files so it can send the proper messages to the POP3 client in order to transfer the email.

HTH,

Gdunge

It means the data can be transfer serially.i.e ,one by one. So it is less in speed.

static nat

compare and contrast the three types of addresses used in a network

message switching: sends the entire message to an alt router route to get to the end user.

packet switching: breaks the message into packets and sends them to the end user, using the path with the lightest load or least traffic at the time of transmit. Packets can be sent in order or not and are re-assembled at the recieving end in the correct order by packet number.

Message switching is a telecommunications data transfer method that was first introduced in 1961; unlike packet switching that came after, message switching sends the entire message as one unit. To transfer the message, the message is first stored and then transferred via hops until it reaches the destination. Most messages are too large for random access memory (RAM), so the messages are temporarily stored in the hard drive. While message switching is not the primary method for data transfer, because it is slower and experiences delays when sending, it is still used widely with sending email. The advantages of this method are lowerbandwidth costs, better management of network congestion, and the easy transfer of messages to different destinations.

When a user sends a message using message switching, this method first saves the entiremessage and then designates an address for the message, so it knows where the message is going. Once saved, the message is sent to the router, which switches it to the first hop, or node. At each hop, the message is inspected for problems or errors before being sent on to the next hop. The message keeps hopping around until it reaches its final destination.

by muhammad kamran from bannu university number=03369797939

Transport Layer, this layer allows data to be broken into smaller packages for data to be distributed and addressed to other nodes (workstations). Main functions are multiplexing, De multiplexing, error control, flow control.

Its not a Router.. they only manage traffic on the network. Servers are specialized COMPUTERS that manage network resources and ALLOW computers access to the network.. BINGO!

Sounds like you are talking about a "Router". A router manages and direct traffic on your local network. Routers make your connection faster and easier. It also makes your local network more secure!

QPSK = Quadrature Phase Shift Keying In QPSK amplitude are not much.so the carrier is constant. transmission rate is higher when compared with PSK

network monitoring describes the use of a system that constantly monitors a computer network for slow or failing components and that notifies the network administrator in case of outages via email, pager or other alarms. It is a subset of the functions involved in network management.

While an intrusion detection system monitors a network for threats from the outside, a network monitoring system monitors the network for problems caused by overloaded and/or crashed servers, network connections or other devices.