Computer Networking

no

this is a class c network address and the subnet mask is by default

255.255.255.0 or /24

On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.

a TcP IPv4 ip address has 32 bits.

Reliable delivery

In GATE 0 represents OFF and 1 represents ON

4.

4.

4.

4.

it = tv

In STP, first a central switch (or bridge, as it it called in STP) is selected - the "root bridge". All other switches calculate the shortest path to this root bridge.

Yes. You are the finding It so what do u think

The atmosphere has four layers. Here is the order of the layer from the lowest altitude: the troposphere, stratosphere, thermosphere, and the exosphere.

Yes, under certain circumstances the coax can carry sufficient voltage and current to be lethal if you make contact with the center conductor and ground, and the voltage enters your body. This might happen if you chance to contact the main trunk cable either coming from a downed aerial line or from an in-ground pedestal.

In practice, the coax in the average home does not carry any appreciable voltage, unless coax-based home phone service is present - and then the ring voltage might be sufficient to shock you if you are in contact with the bare conductors.

url

Time-to-live (TTL)

It's called the internet protocol (IP) address.

i think the next question is " what is the name of the access method used on the LAN?

A network protocol is a set of rules, how to handle communication. These rules may be followed by the endpoints of a communication (computers, printers, etc.), or by intermediate pieces of equipment (switches, routers, etc.), or by both, depending on what particular protocol you are talking about.

A network protocol is a set of rules, how to handle communication. These rules may be followed by the endpoints of a communication (computers, printers, etc.), or by intermediate pieces of equipment (switches, routers, etc.), or by both, depending on what particular protocol you are talking about.

A network protocol is a set of rules, how to handle communication. These rules may be followed by the endpoints of a communication (computers, printers, etc.), or by intermediate pieces of equipment (switches, routers, etc.), or by both, depending on what particular protocol you are talking about.

A network protocol is a set of rules, how to handle communication. These rules may be followed by the endpoints of a communication (computers, printers, etc.), or by intermediate pieces of equipment (switches, routers, etc.), or by both, depending on what particular protocol you are talking about.

in general the router uses the network address to compare to the routing table. Specifically, on the internet, the Router looks up the destination IP address in the router table to determine where to route the packet.

It means connecting different computers and other equipment into a network, so that they can share data and resources.

It means connecting different computers and other equipment into a network, so that they can share data and resources.

It means connecting different computers and other equipment into a network, so that they can share data and resources.

It means connecting different computers and other equipment into a network, so that they can share data and resources.

Networking, in the CLC context, is basically extending the outreach of the resources in different

ways so as to increase the effectiveness of the programme. The areas of operation can also be

increased through networking. Networking can be between CLCs, or with other institutions.

Linkage and networking are different in the degree of commitment by the partners: In linkage, the

relationship between partner organisations is quite loose, while in networking, it is much stronger,

usually because the groups and agencies have common objectives and beneficiaries.

In a virtual circuit network, there is an end-to-end connection in the sense that each router along the path must maintain state for the connection; hence the terminology connection service.

In a connection-oriented transport service over a connectionless network layer, such as TCP over IP, the end systems maintain connection state, but the routers have no notion of any connections; hence the terminology connection-oriented service.

No. Coaxial cable is a single wire that has a thick coating around it. A common use of coaxial cable is for cable television. This is the cable that goes from the jack on the wall into your cable box.

Twisted pair contains multiple cables which are split into pairs and twisted together. CAT5/CAT5e/CAT6 cable are all examples of twisted pair. There are a total of 8 wires inside. Every two wires are twisted together to form a pair. The purpose of the cables being twisted together is to reduce electrical interference between the wires.

A socket is the combination of an IP number and a port number. Often this is written as 10.43.3.87:23.

A socket is the combination of an IP number and a port number. Often this is written as 10.43.3.87:23.

A socket is the combination of an IP number and a port number. Often this is written as 10.43.3.87:23.

A socket is the combination of an IP number and a port number. Often this is written as 10.43.3.87:23.

Advantages: CRC is simple to implement in binary hardware, Mathematical analysis of CRC is very simple, and it is good at detecting common errors caused by noise in transmission.

Disadvantages: CRC is not suitable for protecting against intentional alteration of data, and overflow of data is possible in CRC.

This depends entirely on the use of the cable.

In a full features RS-232 cable there would be 9 cables. But most hardware that uses a serial cable doesn't have the need for all of these wires so the number may vary.

regards,

tesseract