0
Dodge Intrepid
In this category you can ask questions about Dodge Intrepids. These questions can include where to find parts, how to get help, or how to do it yourself.
1,915 Questions
Where is the water pump located on a Dodge Intrepid 2.7L?
It is inside the front of the engine, driven by the timing chain.
Where is the motor mount of Dodge Intrepid located?
There are three. One on the left, one on the right, and one on the back of the transmission.
use small pin to depress ball valve in bottom of tensioner. using fingers compress tensioner. this is to keep the tenioner from exerting too much pressure on the timing chain.
How do you fix vacuum leak on Dodge Intrepid?
A vac leak simply means you have a hose somewhere with a hole in it that needs replaced. An engine generates vacuum so unmetered air will enter any hole where its not supposed to and lean out the mixture. The vacum is used to operate some things like brake booster etc but those hoses must be airtight
Heating problem in Dodge Intrepid 97 3.5?
i have problem my dodge intrepid 97 v6 3.5 overheating just in the machine not a radiator system
Trunk light switch on a 1999 Dodge Intrepid?
Trunk light switch is part of the trunk light socket assembly...
Why does your brake light fuse keep blowing on your 1999 Dodge Intrepid?
Fuses That "Blow" Repeatedly
Without being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.
Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].
Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.
And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.
When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.
The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.
The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].
Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.
Why does the air bag light stay on in 1996 Dodge Intrepid?
You have a problem with the SRS. This is not a DIY repair. Seek out a professional for this repair as working on this system can be hazardous.
How do you get the check engine light to turn off on Dodge Intrepid 2004?
disconnect battery for 30 seconds
How do you replace tie rod end bushings on a 2004 Dodge Intrepid?
First plan to cuss a lot if you are doing this at home in your garage. You will need a tie rod joint separator or a big ol' ballpeen hammer and a large screwdriver... I suggest you invest in the tool, it only costs a couple of bucks and will save you much aggrevation! Make sure the car is safe after jacking it up (use jack stands and wheel chocks). Take note of where the tie rod ends are in relation to the rod itself. If possible, mark the rod before you remove it to indicate where you will want to screw the new end up to. After loosening the nut, gently tap the tool in the rod end to losten it from the bushing. Take the nuts off, screw the new tie rod ends on up to your marked point and then replace to the proper torque settings... you do have a torque wrench don't you? Don't forget about the cotter pins, they will need to be replaced. You will need to have the car realligned no matter what so count on that cost. If you do it mostly right you should still be able to drive it to your allignement station. If not, be prepared for a towing cost! GOOD LUCK!
Will a 2004 dodge neon motor and a 1990 Dodge Intrepid motor the same?
A neon uses a 4 cylinder, an Intrepid uses a 6 cylinder, plus there wasn't a 1990 Intrepid.
How do you use a miller 6642 tool?
when installing a new timing belt and cam sprokets are removed to replace cam seals the tool holds the camshaft in place
How do you remove the crank pully to get access to the water pump on a 2000 intrepid?
You have to use a harmonic balancer puller to remove the pulley You can borrow one from a parts store with a deposit. Just finished replacing the water pump last week on our 1999 Intrepid. Depending on the mileage (if over or close to 100,000) do yourself a favor and replace the timing belt while you are at it. Good Luck
Does the dodge 2.7 liter engine timing have to be set first before changing the chain?
yes it does it needs to have the dot on each sprocket facing each other so the timing is set
What is 2002 Dodge Intrepid trouble code P0463?
Trouble code P0463 means:Fuel level sensor circuit high input
How do you find bank 2 on a 2000 Dodge Intrepid engine?
if its the v6 front wheel drive then its on the side opposite of the radiator or the side of the engine that's towards the rear of the car.
What does error codes p0320 mean on a 2000 Dodge Intrepid?
Trouble code P0320 means:Ignition/distibutor engine speed input circuit malfunction
What could cause antifreeze to pour out of bottom of Dodge Intrepid car?
Failed hose, water pump, freeze plug, intake gasket..........
