0
John Deere
John Deere is the leading manufacturer of agricultural machinery in the world. Questions about John Deere products and their proper operation can be asked here.
2,566 Questions
John deere 318 engine stops mower stops engine will restart but mower deck will not too hot?
Your mower has an electric PTO clutch that is worn out. It clutch stops working when it gets hot. Replace the PTO clutch and you should be fine. Expect to pay about $150 for the part.
What size is the nut on a john deere 60 deck spindle?
The nut on a John Deere 60 deck spindle typically measures 1/2 inch. However, it's important to check the specific model and year, as variations may exist. Always refer to the operator's manual or parts catalog for precise specifications.
Diagram for GX 85 John Deere Riding Mower?
Where does the 2 purple wires under the motor clip back onto
Will Case Baler Needles fit a John Deere 14T Baler...They look the same?
No, they will not fit. Different mounting pads, different length needle arm.
Who makes John Deere riding mowers?
John Deere riding mowers are made by Deere & Company themselves...produced for the last number of years in Horicon, Wisconsin, USA.
Why did my John deere mower blades stop turning?
Operators safety switch, busted belt, or something stuck in deck NB Don't try any maintenance unless you KNOW that ignition is impossible - you need to retain all your fingers!
Why is John Deere 1010 hard to start?
The John Deere 1010 was a beautiful tractor and it had plenty of power, but at times it was hard to start, especially in wet weather.
The earlier 1010's had a round tubing front axle and the later 1010"s had a square front axle.
Many considered the earlier 1010's with the round front axles to be a lemon and one of the worst tractors that JD ever made.
The 1010 was the first JD to switch from the 2 cylinder pop pops and enough reasearch, development and testing was not done before they were manufactured and sold.
JD used old model transmissions and parts and a new style engine which resulted in some long range reliability problems, and starting the tractor was one of them.
One problem they had was that the condensor would burn up rather quickly which would burn the points, thus making it hard to start.
If you change the plugs, points and condensor regularly and often spray the cap and wires with a water proofer it should help.
Remove riding lawn mower rear wheel?
most of them are , one bolt and a snap ring holding the tire so you need some snap ring pliers
It could be several years....they were built in the early 80's, maybe even the late 70's.
A cross reff a john deere air filter he140-2628 and an oil filteram101207 thanks?
You do not mention which brand you want to cross-reference to. The handiest cross reference guide I found was for FRAM filters. The FRAM Filters cross-reference guide lists FRAM CA140 for the JOHN DEERE HE140-2628; and FRAM PH7575 for the JOHN DEERE AM101207
What type of fluid is used in drive system on a john deere 316 lawn tractor?
John Deere all-weather hydrostatic fluid or an equivalent type "F" automatic transmission fluid
What years were John Deere 265 lawn tractor made?
they were made from 1987 to 1991
i looked it up on google
How many John Deere stores are in the US?
There are lots! If you're trying to find a dealer, see the related link...
, You probably have water or dirt in your carburetor which is restricting the main jet. You said that it will run ok in the down position which is the idle position. The idle circuit is separate from the fast idle or running circuit. This carburetor will need to be removed, taken apart, cleaned and inspected. This is not an easy carburetor to get off. I work on John Deere lawn equipment and this is my LEAST favorite carburetor to remove. If you find water and dirt in your carburetor take the time to clean your entire fuel system (tank, fuel lines and fuel pump) otherwise you will have the same symptoms again. Another thing to check is the fuel shutoff solenoid. I have seen the wire fall off this. Sit on your tractor seat, press the brake in and just turn the key on (NOT the cranking position) and if you hear a click the solenoid is working.
What do you do if your John Deere Sabre Riding Lawn Mower stop moving any ideas?
Run out of gas? check spark plugs? I would push it into the garage and call someone who knows about them.
What type of hydraulic fluid does a John Deere 950 use?
Transmission Oil Low Viscosity HY-GARD® (JDM J20D)
How do you remove the rear wheel on a john Deere Sabre 1538?
With these vehicles, there is often rusting to the axle. Therefore, rust remover and lubrication may have to be applied before the wheel can be removed. The vehicle will need to be placed on blocks first, then the wheel should be unbolted.
