Lexus IS

On a Lexus RX 300, the oxygen sensor is typically located in the exhaust system. There are usually two sensors: one before the catalytic converter (upstream) and one after it (downstream). The upstream sensor is generally found on the exhaust manifold or in the exhaust pipe close to the engine, while the downstream sensor is located after the catalytic converter. Always consult the vehicle's service manual for precise locations and specifications.

The exact number of yellow Lexus IS300s produced in 2001 is not publicly available, as Lexus did not typically disclose production numbers by color. However, yellow was a rare color option for the IS300, making it significantly less common than other colors. As such, it is likely that only a small number of yellow IS300s were manufactured during that production year.

The engine number for a Lexus vehicle is typically located on the engine block itself, often stamped or etched onto a flat surface. Common locations include the front or side of the engine, near the timing cover or cylinder head. For specific models, it's best to consult the owner's manual or a service guide, as the exact location can vary.

The Lexus RX 350 typically requires around 6 to 6.5 quarts of engine oil when performing an oil change, including the oil filter. However, it's always best to consult the owner's manual or a dealership for the most accurate specifications, as these can vary slightly by model year.

To fold down the split rear seats in a Mercedes-Benz CLA 250, first, ensure the front seats are not in the way. Locate the release levers on the top of the seatbacks, usually found in the trunk area or on the seat itself. Pull the levers to release the seats, then push the seatbacks forward until they are flat. Make sure to check the owner’s manual for specific instructions related to your model year.

For a 2008 Lexus IS 250, it's recommended to use synthetic oil with a viscosity of 5W-30. This oil type helps ensure optimal engine performance and protection. Always check the owner's manual for any specific recommendations or requirements, especially regarding oil change intervals.

The engine number on a Lexus IS 350 is typically located on the engine block, often on the front or side of the engine, near the timing cover. You may need to look under the hood and check the area around the cylinder head or the oil filter for better visibility. It's also helpful to refer to the owner's manual for specific details related to your model year.

To install a navigation DVD in a Lexus IS250, first, ensure the vehicle is in park and the ignition is turned on. Open the navigation system's DVD slot, typically located in the center console or dashboard, and insert the navigation DVD with the label facing up. Once inserted, the system should recognize the disc automatically, and any necessary updates or installations will begin. Follow any on-screen prompts to complete the setup process.

To determine if the catalytic converter is bad or if it's just the bank 2 sensor, you can start by checking for warning lights on the dashboard, such as the check engine light. Use an OBD-II scanner to read any error codes; codes related to the catalytic converter (like P0420) indicate potential issues with it, while codes specific to the sensor (like P0138 for bank 2) suggest a sensor problem. Additionally, you can inspect the exhaust system for unusual noises or smells, and perform a visual check for physical damage or clogs in the catalytic converter. If the converter is excessively hot or glowing after driving, it may be failing.

To change the windshield wipers on a Lexus ES 300, first lift the wiper arm away from the windshield. Press the tab on the underside of the wiper blade to release it from the wiper arm, then slide the old blade off. Align the new wiper blade with the arm, ensuring it clicks into place when you press the tab down. Finally, gently lower the wiper arm back onto the windshield.

To remove the seat from a Lexus IS300, start by disconnecting the negative battery terminal to ensure safety. Then, locate and remove the bolts securing the seat to the floor, usually found at the front and back of the seat. After removing the bolts, tilt the seat backward and disconnect any electrical connectors for power seats or airbags if applicable. Finally, lift the seat out of the vehicle carefully.

To remove the front hub assembly on a 2002 Lexus IS300, start by safely lifting the vehicle and removing the front wheel. Disconnect the brake caliper and rotor, then remove the axle nut. After that, detach the tie rod end and lower ball joint, and finally, unbolt the hub assembly from the strut and remove it carefully. Ensure all components are properly supported and refer to a repair manual for specific torque specifications during reassembly.

Yes, there is a radio code for the Lexus IS300, which is typically required if the radio is locked after the vehicle's battery has been disconnected or replaced. The code can often be found in the owner's manual, on a card provided with the vehicle, or by contacting a Lexus dealership with your vehicle's VIN. It's important to keep this code in a safe place to avoid future issues with the radio.

In a 2001 Lexus IS300, the fuse box is located inside the cabin on the driver's side. Specifically, you'll find it under the dashboard, near the steering column, and it may be covered by a panel that you can remove. There’s also a secondary fuse box located in the engine compartment, near the battery. Always refer to the owner’s manual for specific details and diagrams.

On a 2001 Lexus IS300, the fuel pump sensor is typically located within the fuel tank, integrated with the fuel pump assembly. To access it, you usually need to remove the rear seat and the access panel or drop the fuel tank itself. It's important to handle fuel system components with care due to potential hazards. Always consult the vehicle's service manual for specific instructions and safety precautions.

To reprogram a keyless remote for a Lexus IS 300, first, sit in the driver's seat and close all doors. Insert the key into the ignition and turn it to the "On" position without starting the engine, then turn it back to "Off" and remove the key. Within 5 seconds, insert the key back into the ignition and turn it to "On" again, then press and hold the "Lock" button on the remote until the doors lock and unlock, indicating successful programming. Repeat for additional remotes if needed, then turn the ignition to "Off" to complete the process.

To reset the PCM (Powertrain Control Module) code on a Lexus IS300, you can disconnect the car's battery by removing the negative terminal for about 15-30 minutes. This will clear any stored trouble codes. After reconnecting the battery, drive the vehicle for a short distance to allow the PCM to recalibrate. Alternatively, you can use an OBD-II scanner to clear the codes directly from the vehicle's diagnostic system.

Different brands, different capacities, different prices. Call your local auto parts store.

RX350:

With the car ignition off, press and hold the ODO Reset button and turn the ignition to the On position. Continue holding the ODO button depressed until the Maintenance Required light extinguishes, about 15 seconds.

Bulbs can be replaced you have to get bulbs type 9006 (hb4)

The ground clearance of the 2008 Lexus IS-250 is 0 ft. 5.7 in. (5.7 in.).