Locks and Latches

Pour warm water were it shuts. Also, if can reach the car with an extension cord you can use a hair dryer.

To reset a Lewis N. Clark 3-dial TSA002 combo lock, do the following: 1) Pull the shackle up and rotate it 180 degrees. 2) Press and hold down the shackle 3) While holding the shackle down, dial in the new combo 4) Release the downward pressure on the shackle and rotate it to the lock position and you're done

Yes. Members of the military can own lock picks. So can everyone else in the United States; even minors.

Padlock

The cost to fix a trunk latch can vary widely depending on the make and model of the vehicle, as well as the specific issue. Generally, repairs can range from $100 to $300 if done at a dealership or a professional mechanic. If you opt for DIY repairs, the cost of parts alone may be lower, typically between $20 and $100. Always check with a local mechanic for a more accurate estimate based on your situation.

To lock objects in PowerPoint, you can group them together, which prevents individual items from being moved or edited separately. Select the objects you want to lock, right-click, and choose "Group" from the context menu. While PowerPoint doesn’t have a direct "lock" feature, grouping effectively secures the arrangement. If you need to edit later, simply ungroup the objects by right-clicking and selecting "Ungroup."

No. It does not require very much power. If the battery is not putting out enough power to turn the starter, but is putting out some power it may still work. If the battery is totally dead it will not work.

use your combination and spin the dial until the briefcase pops open.

A quick way to unlock a breifcase that you have lost the combo to is this;

If it is a 3 digit lock ( 3 on each side ,6 in total , two different combos)

you start at 000 and you hold the unlock "slider" while changing the last number.

now when you just the last number to 1 ( 001) spin the first roller so you will get 101 201 301 and so on. it sounds tedeas but it is fast. just quickly just the last two rollers in sequenze and ever time you just the number spin the first roller. so you will count up to 99 rolls ( shouldnt take that long unless the combo ends in 99.

so for instance if the code is 639. when your get to 039 and spin the roller it will pop open on 639. its alot quicker than doing it one number at a time then trying to open on each number ( 999 entemps lol)

well hope this helps and is not to confusing.

Good Luck

The small holes on padlocks are drain holes that let moisture run out.

this is my little trick i learned when i locked myself out of my contour.. first unscrew the antenna and but two bends in it so its shaped like a S this will work with a clothes hanger too.. then pry the door open with something and push the antenna through the top gap and it will push the door sealer out of the way.. once you can get the wire to the handle just keep turning it till it prys the handle out far enough to unlock the door.. it doesnt take a whole lot of force but it does take a bit of patience and you may need to fine tune the bend in the hanger.. if you cant make that work then you'd have to call a locksmith or someone with a little bit of skill getting in this way

the egyptians

Don't cause once you do you can't unlock it

No. Though it is likely to fit some.

yes. An example of this is a master key otherwise known as skeleton keys.

Lock pick sets are not controlled items in the United States and there is no age limit to purchase them - although stores have the individual right to refuse sales to anyone they choose, which may include refusing sales to minors.

Using the proper key or combination.

Ouch! It will probably be easier and cheaper to just have the whole lock assembly removed and replaced.

***

If the lock can be removed then use "Goof Off" to soak the lock. The wafers can usually be removed and cleaned, just make sure everything is kept in order. But if possible it is usually better to just replace.

Well a half locker, like top and bottom is 12" by 28"

MIT has developed a virtual lock-picking simulation. It is available on Scratch website.

tumbler cut

Yes, a lock washer is typically placed on the screw first, under the head of the screw or nut. Its purpose is to prevent loosening due to vibration or other forces. After placing the lock washer, you then tighten the screw or nut onto the assembly. Always ensure that the lock washer is properly seated for optimal effectiveness.

use a fire hyderant and bang it in a downward motion hitting the lock. do this a couple of times and it should do the trick.

To set your personal cipher, follow these steps:

1- Open the lock (the original number is 0-0-0).

2- Pull lock's hook to the end, hold the position until the third operation had been performed.

3- Set your secret code by turning the wheels then release the hook.

4- Press the hook into lock's slot, turn the wheels to the other cypher, the hook can't be pulled. it is locked.

don't now and don't care