0
Marlin Firearms
Marlin firearms are manufactured by the 130-year old Marlin Firearms Company in North Haven, Connecticut, USA. Throughout the years, different kinds of firearms have been produced such as rifles, derringers, shotguns and revolvers.
3,064 Questions
What is the age of a 30-30 Marlin Limited Edition 3080 serial start with TR00126?
What is the age of a 30-30 Marlin Limited Edition 3080 serial start with TR00126
Can you fire 44 Special and or 44 mag out of a 444 Marlin rifle?
No, you can not. The 44 Special can be fired in any firearm chambered and marked for the 44 Magnum cartridge. The 444 Marlin is a rifle cartridge (much longer than either the 44 Spl or 44 Mag), and is much more powerful. The 44 Spl and 44 Mag. were designed as handgun cartridges, but have been adapted to a small number of lever-action carbines. Bert H.
Magazine for a marlin glenfield 25?
Marlin still sells them, but I've seen them at Gander Mountain. Make sure the release lever is on magazine before you buy, Marlin had a bad batch w/o them made and distributed accidentally.
What year was a lever action marlin model 1936 32 special serial no 702 manufactured?
The 1936 Marlins were made in 1936 & 1937.The marlin model 36 came in three different variations.The model 36 first variation was marked model 1936 on the upper tang and was made from 1937-1940 and had no letter prefix to the serial number.The second variation had the same markings on the upper tang,but had a heavier buttstock and no longer had a fluted comb.The buttplate was thicker also with a slightly curved style,and the forearm was a heavier beaver style.The letter B was the prefix to the serial number.The third variation was offered in 30-30,or 32 Win Special,no upper tang markings.Rifles had a letter A suffix,sporting carbine had a SC suffix,and regular carbine had a RC suffix.The the prefix had a small letter C in 1946,and large letter D in 1947.The second variation was made in 1941 only,while the third variation was made in 1946-1947.
What is the age and value of a harrington and richardson 20 gauge single barrel shotgun model 58?
about 80 bucks. I have seen them go for 130, and have seen them go for 2 for 50. Just gotta find the right person.
Where do you get parts for marlin 60w rifle?
Marlin Firearms Parts & Service 1-800-544-8892 Best customer service in the firearms industry.
What is the year of a 22 SLLR Glenfield marlin model 25?
Before asking these questions one might search the list to see if this question had been asked and answered.
An iteration of a answer on this is "from 1968- 1973 the year is the first two digits in the (sic) serial from after 1973 subtract the first two digits from 100 (ex 2011645 - 100-20=80). before 1968 there are no serial # on .22 cal firearms."
This should help you determine the year of manufacture in regard to Glenfield/Marlin model 25.
As an example: my dad bought me a Glenfield/Marlin 25 from the local JCPenney for 42usd. I do not know why I remember that but maybe it was a lot of money in those days.
My serial number is 72422xxx, I will not show the last three digits of my serial for the sake of privacy.
My serial started with a 72 for the year 1972. That is correct because he bought it for me as a gift the spring of 1972; for rabbit hunting.
Some would say the Glenfield had no swivels for a sling but mine did and some would say the trigger should have been black but mine is chrome. Just some added information.
Good luck and peace be to the journey!
How hard does a marlin 35 Remington kick?
well that's a hard question. its all a scientific equation with the weight of gun bullet and length of barrel. it also has to do with add ons (barrel break merckury ttube(s) and butt pad) also lever semi or bult. on averiage a little less than a 12 gage straight out of the box how ever a semi autto will not kick as much as a single action.
My Marlin Model 336CS in 35 Cal with the 200gr bullets has a surprisingly light kick
How do you install an extractor for Glenfield Model 30A?
Disassembling a Marlin Glenfield 30A action for cleaning and maintenance.
Field stripping the Action of a Marlin Glenfield 30A..
First visually make sure the weapon is unloaded by opening the action and checking the chamber and feed ramp for cartridges..
Leave the action fully open and lay the rifle on a clean flat surface such as a padded bench or table..
Using a good quality tight fitting flat blade screwdriver remove the lever pivot screw..
Pull the lever free of the bottom of the action and out of the frame..
Grasp the bolt and pull it rearward out of the frame..
The EXTRACTOR is a single stamped piece of spring steel that grips around the bolt and is removed by carefully prying it free..
Clean the bolt with solvent and a small brush then wipe dry and apply a small amount of heavy gun oil or petroleum jelly to the machined depression in the bolt where the extractor grips it and also to the new extractor..
Push the new extractor onto the bolt until it is seated completely then check for proper clearance of the claw to the bolt face by placing a spent shell on the bolt face..
If the claw does not grasp over the rim of the shell and hold it in place over the bolt face try to wiggle the extractor at the point it clips onto the bolt to make sure it is seated properly..
If this fails to achieve the proper clearance you may need to remove the extractor and file the claw until it grasps the rim of the shell correctly..
Wipe away any excess lubricant and apply a light coating of gun oil to the entire bolt..
Clean the inside of the frame with gun solvent and a brush taking care to clean around the ejector lever in the back of the action.. You can remove the ejector by simply pushing on its post which is visible at the rear outside flat opposite of the ejection port.. Wipe dry and lightly lubricate all contact surfaces inside the frame..
Reassemble the bolt back into the frame the same way it came out and reinsert and attach the lever with the pivot screw..
What does the RC mean in the Marlin 336?
The RC stands for Regular Carbine, the R was later dropped and just 336C used to describe the Carbine style. The style refers to the barrel bands that also go around the forearm.
What is the best ammo for hunting with a Marlin 30-30?
Read your manual, or request a free catalog from Marlin. Factory load is always what they recommend.
Where can you get a clip for a marlin glenfield model 20?
Call Marlin Customer Service 800-544-8892. Place orders there. Part # 504046. Glenfield 20 is same as Marlin Model 780, except for the wood.
What does the c mean in Model 336c Marlin rifle?
The C stands for carbine. Here is a list I've found concerning the rest of the letters:
CS .... Carbine Safety
C........ Carbine. 1968 and up
RC......Regular Carbine same as C prior to 1968
T .......Texan. Carbine with straight stock, 20 inch barrel
TS.......Texan Safety with 18.5 inch barrel.
SC.......Sporting Carbine, 20 inch barrel, 2/3 mag tube, pistol grip.
CB.......Cowboy, 24 inch octagon barrel and straight stock.
A.........Prior to 1980 24 inch round barrel PG stock
A........ Most recent, 20 inch PG carbine with birch wood, end cap forend.
W........ 20 inch PG carbine, birch wood, and two barrel bands
Y......... Spikehorn youth model short PG walnut stock 16.5 inch barrel.
LTS...... Texan Safety, 16.25 inch barrel.
Marauder.. same as 336 T except has 16.25" barrel and SG. Roll marked RC.
ER......... Extra Range PG stock in 356 Winchester.
375....... PG stock 20 inch barrel in 375 Win.
XLR.......Stainless steel 24 inch barrel PG laminated stock
CC....... 20 inch carbine with camo pattern birch PG stock
SS........20 inch PG stock Stainless steel.
ZG....... Zane Grey Century PG stock, 22 inch octagon barrel.
336 Octagon.. 22 inch octagon barrel SG stock.
336BL.... big loop lever and laminated PG stock.
Looking for parts for a Glenfield Model 60 auto loader?
Call Marlin Parts and Service, 800-544-8892. You'll need to provide model and serial number. If gun too old, they'll refer to companies that may have older parts.
How do you replace the spring in the trigger mechanism in a marlin 49dl 22 semi automatic rifle?
Best left to a gunsmith.
Where can you get marlin 39a parts?
For most 39A, you can call Marlin's Customer Service, 800-544-8892. They handle parts and repairs. This all depends on the age of the gun (which is determined by the serial number). Parts may not be available, if gun is too old. They have some referrals to companies that may have parts for the older guns.
