Mazda

Well, your best option is to voluntarily return the car before a repo order is put out on it. It may reflect on your credit that you defaulted on the loan, but it will be much worse if you establish a history of non-payment and involuntary repossession. Talk to the dealer, bak, or whoever it is who has the lien on the title and see if you can work out another payment arrangement. If you can't keep the car, then voluntarily turn it in.

intake? carb or injected (b2000,b2200 or b2600i) b2000 and b2200 pull the air cleaner and hoses ( watch were the vacuum lines go and unhook the little white 2 wire plug on the front) remove the fuel lines from the fuel pump ( on the pass. back of the head) remove the top and bottom manifold nuts. remove the throttle cable ( try not to loose the spot were it is on the shaft. you might be able to wiggle it out of the holder) you can use a long extension to get to the under side nuts and pull the bypass tube back out of the way. pull the manifold back and clean all of the old gasket off . clean the head and put new gasket in DRY (do not use silicone or gasket compound)

Depends on the engine, but on the 4 cylinder models if you open the bonnet, and stand with the car facing you, the oil filter is right in the middle, on the back of the engine (Facing away from you). Its screwed in, and you may find it easier to drain it by puncturing it with a screwdriver before you try and unscrew it, because else it'll spill everywhere (It holds a surprising amount!)

It sounds like low fuel pressure could be a real possibility. It could be a partially blocked filter, weak fuel pump or a faulty fuel pressure regulator.

It's probably leaking from a faulty water pump. Replace the pump.

Fuel filter for Mazda B3000 pickup is mounted within the left frame rail

An engine burning oil will produce blue smoke. White smoke from the exhaust is an indication of coolant entering the combustion chamber. This is caused by either a blown head gasket or a cracked head. Stop driving this car and have it looked at by a professional.

left frame rail between tank and engine

The fuel filter is mounted within the left frame rail. To disconnect the push-connect fittings from the filter, you will need a special tool available at most auto parts stores.

Depends on where the dent is located.

The fuel filter is located with the frame rail on the driver's side and requires quick disconnect tools to change it. You are probably better off having it done the next time you have it serviced since even the cheap disconnect slip rings will cost you ten dollars and you will probably never use them again.

the easiest way to find the filter is to locate the fuel line and trace it foward, the filter will be inline. hope it helps. duboff

Residual-based financing has lender-specific rules ( GMAC, FMC, Mazda American Credit, etc. )so read your contract section that pertains to " Early Termination." Your agreement should state clearly and specifically what your rights/options are if you terminate the loan agreement prior to maturity. Normally you CANNOT return the vehicle prior to maturity without substantial penalties ( early termination fees ). At the very least you would probably be liable for a deficiency if the vehicle is worth less than you owe. Consider selling the vehicle or trading-in for another car/truck ( both of which you may do at YOUR discretion,at least on any Smartbuy/Gold Key Plus/Red Carpet Option agreement I've ever seen )that better suits your needs. If you're still unclear about the early return consequences contact the lender directly and note the time, date and name of the person you spoke with and the specific advice you were given.

-David

it should be near the gas tank above the fram rail

To replace dash lights on a Mazda B 3000 first disconnect the battery and remove the dashboard. Unplug the cluster wiring and carefully remove the display. Replace the lights.

turn your steering wheel all the way to the left, get your 10mm socket with 1/4" ratchet wobble and 2x 2" extensions and remove the several bolts holding the dust cover from inside the wheel arch. Then proceed to remove the existing broken antenna (you will need to reach up into the guard to hold the antenna) and using a 14mm ring spanner undo the topmount fitting on old antenna, Then Reverse (the antenna cable goes through the side behind glove box just trace it and replace that with new cable that comes with new antenna) or you could just cut and solder the old cable to new antenna.

This tech tip pretty much says it all: http://www.asashop.org/autoinc/sept2002/techtips.cfm

If the blinker is not working on a Mazda 121, check the turn signal flasher. If the bulb needs to be replaced, remove the lens cover and insert a new bulb.

There is a notch on the crank pulley line that up with the arrow on the block

above the crank, there are dot notches on the cam shaft pulleys line thoughts with the arrows on the top front of the heads. When all are lined up the engine is timed.

the fuel filter is in line on the fule supply line just forward of the gas tank. it is located along the frame just forward of the gas tank (if it's like the b4000 it's on the driverside, tucked up into the inside of the frame)

Im not 100%, but when i have changed other brakes like those in the past there was and Alan wrench bolt towards the inside of the truck, just take take that out and u should be able to figure it out from there, im not sure but i think you can just take them off by removeing that bolt but their might be something else you have to do...

I have a 1986 Mazda familia/323, whose heat light is on. I was told it was the catalytic converter that has collapsed. Infact it had and I dismantled the exhaust system and found bits of the catalytic in the muffler. I dismantled the rest of the system and found where the converter was. I removed all the catalytic and reassembled the exhaust. Guess what? the light is still on! So I am still ssearching for more info.

http://www.therangerstation.com/tech_library/pdf_documents/ToyoKoygoMazda.pdf Hope this helps...

6.5 or 6 1/2 in front and 6 x 9 speakers in back.