0
What else can I help you with?
Which two parameters are stored in the routing table?
the best route to reach remote networks the interfaces used to forward packets
What does a distance vector routing protocol let a router know about remote networks?
The availability of networks, and the metric (or "cost" or "distance") to reach them, according to the system used by the routing protocol to calculate this "metric".The availability of networks, and the metric (or "cost" or "distance") to reach them, according to the system used by the routing protocol to calculate this "metric".The availability of networks, and the metric (or "cost" or "distance") to reach them, according to the system used by the routing protocol to calculate this "metric".The availability of networks, and the metric (or "cost" or "distance") to reach them, according to the system used by the routing protocol to calculate this "metric".
What is true about the metrics used by routing protocols?
Metrics used by routing protocols are used to determine the best path for routing data packets. Different routing protocols use various metrics such as hop count, bandwidth, delay, load, and cost to make routing decisions. The choice of metric can impact the efficiency and effectiveness of the routing protocol in selecting optimal paths.
Is routing better or broadcasting in wireless networks?
They are both required, but some cases broadcasting has to be avoided, for instance, in the case when you are trying to establish connection with remote computer to check your bank account.
Can anyone say you the diff between routing and broadcasting in wireless technology?
Routing was design to avoid broadcasting. It basically means that when you establish connection with remote computer you send messages only to the computer and nobody else. Broadcasting is opposite to routing, and it was design to explore networks around you. When you send a broadcast signal you send to everybody in the specified network.
What are the requirements in order for you to write ccnp certificate?
A CCNP is a Cisco Certified Network Professional. Requirements to attain this certificate involve two semesters of training in topics such as advanced routing, remote access networks, advanced switching, and optimizing converged networks. Extensive exams must also be passed.
Which device should be used for routing a packet to a remote network?
router
How is IGRP similar to RIP?
Interior Gateway Routing Protocol (IGRP) IGRP is a distance-vector interior gateway protocol (IGP). Distance-vector routing protocols call for each router to send all or a portion of its routing table in a routing-update message at regular intervals (every 90 seconds) to each of its neighboring routers. As routing information proliferates through the network, routers can calculate distances to all nodes within the internetwork. IGRP uses a combination (vector) of metrics. Internetwork delay, bandwidth, reliability, and load are all factored into the routing decision. Network administrators can set the weighting factors for each of these metrics. IGRP uses either the administrator-set or the default weightings to automatically calculate optimal routes.Routing Information Protocol (RIP) The Routing Information Protocol (RIP) is a distance-vector protocol that uses hop count as its metric. RIP is widely used for routing traffic in the global Internet and is an interior gateway protocol (IGP), which means that it performs routing within a single autonomous system. RIP only uses hop count to determine the best route to a remote network, RIP has a maximum hop count of 15, 16 is deemed unreachable. RIP works well in small internetworks, but is inefficient for large networks. RIP is susceptible to all the problems normally associated with distance vector routing protocols. It is slow to converge and forces routers to learn network information only from neighbors. RIP version 1 uses classful routing (all devices in the network must use the same subnet mask because RIP version 1 doesn't send updates with subnet information). RIP version 2 uses classless routing and does send subnet mask information with route updates. RIP networks need the same hop count to load balance multiple links.
What is Routing and Remote Access Services for Windows Server 2008?
The Routing and Remote Access Services for Windows 2008 is always accepted with a VPN or RRAS. That is all Windows 2008 can handle, along with R2 and an LAN network.
What is Remote infrastructure management?
Remote Infrastructure Management (RIM) is defined by analysts as the remote support and management of various IT services that are related to infrastructure support from global delivery sites. The service offering encompasses remote monitoring and management, which includes support, administration, maintenance, troubleshooting, and performance enhancement. These services include the remote system monitoring of the following: data center, networks (WAN and/or LAN including switches, routers, and hubs), database administration, desktops, servers and related peripherals and e-mail systems.
Can I use two routers together to extend my wireless capabilities?
Yes -- there are multiple configurations but typically two routers can be connected by wire to cover different remote areas on the same network.
In computer what does ra stands for?
RA may stands for: Registration Authority, Risk Assessment, Remote Access, Routing Arbiter, Remote Adapter, Remote Assistance, Restricted Areas
