0
What else can I help you with?
What is the required code for toilet clearance in a residential building?
The required code for toilet clearance in a residential building is typically 15 inches of clearance on each side of the toilet and 21 inches of clearance in front of the toilet.
What are the toilet space requirements for a standard bathroom renovation project?
The toilet space requirements for a standard bathroom renovation project typically include a minimum of 15 inches of clearance on each side of the toilet and a minimum of 21 inches of clearance in front of the toilet. Additionally, the toilet should be positioned at least 15 inches away from any walls or other fixtures.
What is the toilet clearance code for residential bathrooms in the United States?
The toilet clearance code for residential bathrooms in the United States typically requires a minimum of 15 inches of space on each side of the toilet and a minimum of 21 inches of clear space in front of the toilet.
What are the toilet clearance dimensions required for proper installation?
The toilet clearance dimensions required for proper installation typically include a minimum of 15 inches of space on each side of the toilet and a minimum of 21 inches of clear space in front of the toilet. These dimensions ensure proper access and functionality of the toilet.
How difficult is replacing toilet seat cover?
If we're speaking of a standard American toilet set, they're very easy to replace. The only consideration is how much room you'll have to wiggle around on either side of the toilet. Most seats are held on by two bolts on either side of the bowl where the hinge is. Sometimes the top of the bolt is covered by a pop-up piece of plastic or something. You'll need to lie on your side and reach back to the underside of the toilet - feel up under the bowl just ahead of the tank, and you'll find the bolt for that side. It probably has a plastic nut on it. Loosen the nut (you may need a pair of pliers) and simply run the bolt all the way off the nut. Do the same on the other side. Take off the old seat, put the new one on, and reverse your actions. All standard toilet seats will fit any standard toilet.
What should you do when the tip of the toilet auger break off in the toilet?
Remove the bowl turn it up side down and remove theauger head
What is Toilet flange to wall clearance?
12" from rear wall, 16" to 18" to side wall, these are measurements to the center of the flange.
Where can I find the flush button on an airplane toilet?
The flush button on an airplane toilet is typically located on the top or side of the toilet bowl. It may be a button, lever, or sensor that you can press or activate to flush the toilet.
How do I install a toilet myself?
Installing a toilet is not an easy, do-it-yourself task. It takes skill and precision to complete all the steps necessary. This is possibly the single, most troublesome fixture to install as it requires its own 2" minimum vent and a drain of at least 3" in diameter. If the toilet is situated on a branch drain, it cannot be upstream from the sink or shower. The minimum side distance allowed from the center of the toilet bowl to a wall is 15 inches, and 12 inches from the center of the bowl to a bathtub; clearance from the front of a bowl to a wall or fixture should be 21 inches. You can find further do-it-yourself instructions from a local hardware store that sells plumbing equipment.
What could cause water in the toilet bowl to swirl counter clockwise?
You live in Oz (other side of the earth)
How do you properly flush the toilet?
To properly flush the toilet, simply press down on the handle located on the side of the toilet tank. This will release water into the bowl, effectively removing waste and sending it down the drain. Make sure to hold the handle down until the water has completely flushed the bowl.
Standard height for toilet?
There is no standard size. But you should review your local building codes to make sure all clearances are met. Where I am from the center of the toilet must be 15 inches from the wall. This means the narrowest room allowed would be 30 inches wide. Again there must be a specific distance from the front of the bowl to the wall. This number is different depending on where you build. I wouldn't sugest the minimum unless you are tight on space. My advice would be to try out some public bathroom stalls until you find one that's just right. Then measure it.
