0
How do you install a crankshaft position sensor on a 1996 Pontiac grand-amand where is it located?
Wiki User
∙ 16y ago
If the engine is a 3100 V6, the crankshaft sensor is located behind the harmonic balancer (crankshaft pulley). You'll need a special puller to remove tha balancer. The sensor is attached by two bolts onto the timing cover. Replace sensor and plug it in. Repalce balancer& belts...you're done!
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Where is the location of the crankshaft position sensor on a Pontiac grand am 2.4 liter and how to install it?
right above the oil filter
How do you install crankshaft position sensor 95 mercedez Benz c220?
How do you install crankshaft position sensor 95 BENZ C220?
Install crankshaft position sensor on 2004 Maxima?
where is the crankshaft position sensor on a 2004 maxima
How do you install a crankshaft position sensor on a 2001 dodge diesel ram 2500?
ramdom much
Where is the camshaft position sensor on a 2002 Dodge Intrepid?
CRANKSHAFT POSITION SENSOR The crankshaft sensor is located on the passengers side of the transmission housing, above the differential housing Crankshaft Position Sensor The bottom of the sensor sits above the drive plate REMOVAL Disconnect electrical connector from crankshaft position sensor. Remove sensor mounting screw. Remove sensor. INSTALLATION Install sensor and push sensor down until contact is made with the transmission case. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque. Connect electrical connector to crankshaft position sensor.
How do you replace the crankshaft position sensor on a Chrysler PT Cruiser?
The crankshaft position sensor on the PT Cruiser is on the side of the engine above the oil filter. The sensor is removed with two screws. Unplug the wiring, remove the bolts, then install the new sensor.
How do you install a crankshaft sensor on scion?
log on then you have to go to file then it should say install crankshaft to scion user. Click it then follow the instructions given.
How do you install a 1996 Pontiac Grand Am SE?
Install what?
How do you install a CrankShaft Sensor in a 95 Buick Century?
Pull the front cover off of it, Behind the Crankshaft balancer, The sensor is there. a diagram of how to install a creckshaft sensor.
Where is the crankshaft position sensor located on a 1999 Volvo v70?
It located on the drivers side engine compartment over top of the transmission you will need to remove the battery tray to install'
How do to install oxygen sensor on 2006 Pontiac torrent?
We are asking how to remove and install a oxygen sensor for a2006 pontiac torrent.
How do you replace crankshaft sensor on Chrysler sebring 2000?
CRANKSHAFT POSITION SENSOR - 2.5L REMOVAL Remove speed control servo from driver's side strut tower. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor Pull crankshaft position sensor straight up out of the transaxle housing. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector. INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor. NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque. Connect crankshaft position sensor electrical connector to the wiring harness connector. Attach connector to heater tube bracket. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque. extra steps for Simplification added by Billebones@AOL.com: Also: Jack up car and put it on jackstands Remove left front tire, remove plastic shield covering the battery then use a long extension with a 10mm socket to remove and install the bolt holding the sensor right over the top of the axle, this definitively simplifies getting at the bolt, if you have someone up on top to guide it back in it will be even easier. I did not remove heater tube bracket and I plugged it together before I put the sensor into the bell housing
