0
I found crank in a nestles crunch bar made in the bar. What should I do?
Wiki User
∙ 14y ago
It's probably nothing, the bar most likely just got moved around and jostled until it cracked a little. It should still be perfectly fine. If you are worried, just throw it out, though.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where is the O2 sensor and crank sensor located on a 91 Chevy Lumina 31L and is it fairly simple to replace yourself?
I have a 92 lumina with a 3.1 and I found the crank sensor to be located on the passenger side of the engine in the back of the engine NOT on the side of the engine below the knock sensor. Hello, in my experience, all O2 sensors are located in the exhaust just after the manifold. It appears easy enough to change. If it is the crank position sensor you are looking for, take a look around the main pulley at the bottom of the engine, you may see a square-ish component located close to the actual pulley wheel, this would be the crank position sensor, it should have wires connected to it.
What should you do if your teacher found out you were plagiarizing?
if she found out then own up to your mistake
Your 1991 4 runner will not stay crank and it loses power Also you have to start it with starter fluid what is wrong?
if you mean it doesnt crank long enough to start you probably need a battery. i suspect that the battery is dead because it takes so long to start. long crank times on these engines is usually caused by a bad cold start injector (found in the intake plenum on the passenger side, it has a small diameter steel fuel line and a 2 wire plug connected to it. held in place by 2 10mm screws) or the cold start injector time switch (found in the back of the engine behind the intake plenum, it sits in an aluminum casting that holds other water temp sensors and has a blue plug with 2 wires on it). replace these 2 items and you should be fine as far as hard starting goes.
Where is the crank sencore on 97 Chevy vencer van 3400?
The 1997 Chevy crankshaft sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft sensor.
On a 1990 Acura Integra RS is the crankshaft pulley bolt reverse thread?
No - The crankshaft bolt will loosen counter-clockwise. Because the crank bolt is so hard to remove it can seem as though it is reversed threaded. The crank turns the opposite direction that is used to tighten the bolt. For the crank bolt Lefty-Loosey (counter clockwise), Righty-Tighty (clockwise) apply here. The crank bolt is tightened to 87 ft/lbs of torque. It took more then 87 ft/lbs of torque to loosen my crank bolt. The manual says to apply a drop of motor oil when reinstalling the bolt. An Harmonic Balancer Pully Holding Tool is used to hold the crank while working with the crank bolt. Holding Tools can be found on the internet for $20 to $73. There are two sizes, 45 mm and 50 mm. For a 1990 model year the size is 50 mm. I made an Harmonic Balancer Pully Holding Tool by tack welding a 2 foot length of 1 1/2 inch by 1/2 inch piece of stock, for a handle, on a 2 inch (50 mm) hex nut. The nut fits into the pully to hold the crank and the socket, used to turn the crank bolt, fits through the nut.
Who found out potato chips crunch?
anyone who eats them or hears someone eat them
What is crunch?
Captin Crunch is breakfast cereal, that kid's enjoy. It can be found in different stores such as A&P, Shop Rite, Stop Nd Shop, BJ's and much more.
Where can one purchase Cinnamon Toast Crunch?
Cinnamon Toast Crunch is a breakfast cereal that is available for purchase from a number of stores. It can generally be found in any supermarket or grocery store, such as Stop and Shop or Target.
What is the name of the sensor located by or behind the harmonic balancer?
crank shaft sensor With the limited information you have provided, I would have to say, that you have found the "Crank" sensor.
Where is the location of the Crank Sensor on a 3.1 Corsica Engine?
The Chevrolet Corsica 3.1 liter engine crank sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crank sensor.
95 Lincoln Continental will not start?
I had the same problem and found out it was the crank shaft sensor!
Would a defective crank position sensor cause a 1997 Dodge Caravan not to start?
It is possible, but not guaranteed in every case. The crank position sensor is a little bit redundant, since there are other sensors available to the engine's control module, which could give it essentially the same data required for the engine to start and run. Regardless, if the crank position sensor is found to be defective, it should be replaced.
Is there an interchangeable part for 1994 mustang window crank handle?
The interchangeable part for a 1994 Mustang window crank handle would be a 1991 to 1993 Mustang window crank handle. This part can also be found at some salvage yards for automobile parts.
Where is crank sensor on Vauxhall zafira?
The crank sensor for a Vauxhall Zafira is not located in the fuel pump, as is normally expected; instead, the crank sensor in a Vauxhall Zafira is found on the bell housing, situated so that the end of the sensor almost sits against the flywheel.
Is banana nut crunch discontinued?
No I just found it on the shelves this week under the "Post Great Grains" label. New package, same cereal.
How many calories does a bowl of captain crunch cereal with milk contain?
According to the Cap'n Crunch website, a serving of 3/4 Cup (27 g) contains 110 calories, 15 calories of which are fat. Note that that is dry cereal, and the addition of milk will contribute to more calories.
If a crank sensor fails will the car not start?
no the car will not start there normally found on side of gear box.
