answersLogoWhite

0


Best Answer

The clutch trow out bearing has failed

Change the clutch before it explodes and does serious damage to the transmission.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: My Mazda b2500 makes loud rattling sound when i push the clutch in to shift into first gear why?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

Is rattling a verb?

According to several online dictionaries: no. It is only an adverb or adjective I would have thought so, but... >_< It depends: "rattling" can be a verb, but it is not always a verb. "Rattling" is the present participle of the verb "rattle". It is used as a verb in sentences like, "The flimsy door was rattling in the wind." It can also be used as a noun (this is called a gerund), in sentences like "The constant rattling of the screen was annoying." And, as the first answerer noted, it can be used as an adjective: The rattling windows were a sign that the wind was getting stronger. One dictionary gave "a rattling good time" as an example of using "rattling" as an adverb, but this usage is not common.


How do you know if your clutch is going bad?

Slipping of the clutch and a peculiar smell are the first signs of a clutch that is worn out.


How do you replace a clutch cable fork on an Escort 1.8 diesel?

To replace a clutch cable fork on an Escort 1.85 diesel, first lift the clutch pedal to release the adjuster mechanism. Pull the cable through and hook the clutch cable fork.


What would cause a 1995 Mazda 929 to make a rattling noise in the rear that is audible when the car gets warmer but not when first driving off?

That would probably be a heat shield on the exast system.The will not raddle until it heats up and the metal expands.The easiest and cheapest way to fix it is to just take it off.It should not effect anything.It's just something that is more of a anoince than anything else.Hope that helps.Good luck


Why will a car not go into gears It starts but when you move the shift into a gear. The car does not move.?

I am assuming this is an automatic transmission. The transmission fluid could be low, the filter could be plugged or your transmission could be cooked. Don't drive it, don't even try until a mechanic looks at it, could save you a thousand bucks (to replace the tranny) by letting a mechanic look at it first. If it's a standard transmission, your clutch could be worn or burned out, or the clutch release bearing has failed, or your mechanical clutch linkage (if equipped) has become bound or disconnected, or the hydraulic clutch system (if equipped) is low on fluid or has failed somewhere. Also there is a possibility that the differential is blown. Another possibility the e-brake is stuck on.

Related questions

How do you fix Mazda mx 6 clutch sinking to the floor?

First you need to find out if your slave cylinder is leaking clutch fliud.check lines to slave cylinder from master clutch cylinder if no leaks most likely master clutch cylinder bad.


Where is and how do you replace 91 Mazda 626 DX clutch slave cylinder?

The clutch slave cylinder on a 91 Mazda 626 DX is located on the clutch bell housing. To replace the unit, first remove the hydraulic line and turn the line cap counterclockwise. Remove the two bolts holding the slave cylinder in place. Reverse directions to install new unit.


Why is it hard to shift into first gear on a 1994 Mazda B400 4x4?

The shift gate or the synchronizers can be worn. Also the clutch can need adjustment if possible.


I have a 1993 Mazda protege that will shift in all gears with clutch out and engine running but will not move is it a clutch or trannsmission?

Well first of all, if your talking about a manual shift, the clutch is. more or less part of the transmission. Sounds to me like your clutch pad / disk is worn out or you burned it up. Which can happen if you slip the clutch all the time at stop lights / signs. In that case you should probably replace the clutch plate and disk replaced, and have your flywheel resurfaced.


Is rattling a verb?

According to several online dictionaries: no. It is only an adverb or adjective I would have thought so, but... >_< It depends: "rattling" can be a verb, but it is not always a verb. "Rattling" is the present participle of the verb "rattle". It is used as a verb in sentences like, "The flimsy door was rattling in the wind." It can also be used as a noun (this is called a gerund), in sentences like "The constant rattling of the screen was annoying." And, as the first answerer noted, it can be used as an adjective: The rattling windows were a sign that the wind was getting stronger. One dictionary gave "a rattling good time" as an example of using "rattling" as an adverb, but this usage is not common.


What would cause a 1988 Mazda 323 to not have or have very little power from first to second gear Or to have to gear down going up hills?

I had this problem several times and brought it to my mechanic. He informed me that the clutch was going bad thus resulting in a loss of power. Fixed the clutch and my problem dissappeared!


How do you know if your clutch is going bad?

Slipping of the clutch and a peculiar smell are the first signs of a clutch that is worn out.


Why does my car makes rattling noise when first driven and then goes away?

The batter is low


Who designed the Mazda logo first?

The first ever Mazda logo was designed in 1934. The name 'Mazda' represented a combination on the ancient Persian god of light, Ahura-Mazda and also Jujiro Matsuda, the founder of the Mazda Corporation.


When was the first clutch made?

When was the first car made.


When was the Mazda e2000 first manufactured?

The Mazda e2000 was first manufactured in January of 1964. You can learn more information about the Mazda line of vehicles online at the Wikipedia website.


How do you do a burnout on a dirt bike?

put it in nutral, give it some gas and shift up to first. if it has a clutch,pull in the clutch, shift to first,keep the clutch pulled in, give it alot of gas shift to 2nd then let go of the clutch fast.