I hope I am reading this correctly. If so, this already happened to me in my 2003 low-miles Montana EXT cab. I was sooo embarrassed! I had inadvertently turned the dial type instrument-dash light dimmer knob located to the left of the steering column on the dash, to the "dome light on" position which overrides everything else. As soon as I realized this and set it back to a normal brightness level, thereby turning off the dome light override switch, everything else worked properly once again! Hope this helps!! Now if someone could only get me an answer to my inoperative radiator cooling fan problem!!
The 1999 Dodge Durango overhead console wiring connections are beneath the overhead console. You will need to remove the overhead console?æin order to access the wiring connections.
In ebay.com, search by overhead console.
how to I remove the overhead console on the S 10 Blazer?
To remove the overhead console you will first need to disconnect and isolate the negative battery cable. Remove the overhead screws and pull straight down on the console.
Remove the Toyota Camry headliner. The overhead console retaining screws will be visible. Remove the retaining screws and the console will come off.
Take overhead console apart and look inside for any thing loss. It maybe as simple as a clip.
You will need to remove the headliner. With the headliner removed you will be able to see the overhead console retaining screws. Remove the retaining screws.
Remove the screws that hold the headliner in place. With the headliner removed the overhead console retaining bolts will be visible. Remove the retaining bolts. Remove the wiring harness from the console.
Engine, trans, abs, airbag, cluster, overhead console, information center,Engine, trans, abs, airbag, cluster, overhead console, information center,
I googled "04 Dodge Ram Manual" and downloaded the service manual from one of the links, which is different than the owners manual. The service manual is 2000+ pages long....here's what is says about the overhead console removal procedure....REMOVAL OVERHEAD CONSOLE REMOVAL (1) Disconnect and isolate the negative battery cable. (2) Remove the overhead console retaining screws, located in the sunglass storage bin. (3) Using your fingertips, grasp the sides of the overhead console and pull straight down evenly to disengage the two snap clips at the front of the unit. (4) Lower the overhead console far enough to access the wire harness connectors. (5) Disconnect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (6) Remove the overhead console from the vehicle. INSTALLATION (1) Position the overhead console in the vehicle. (2) Connect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (3) Grasp the sides of the overhead console and push straight up evenly to engage the two snap clips at the rear of the unit. (4) Install the overhead console retaining screw, located in the front of console. Torque the screw to 1.2 N·m (10 in. lbs.). (5) Connect the negative battery cable. I googled "04 Dodge Ram Manual" and downloaded the service manual from one of the links, which is different than the owners manual. The service manual is 2000+ pages long....here's what is says about the overhead console removal procedure....REMOVAL OVERHEAD CONSOLE REMOVAL (1) Disconnect and isolate the negative battery cable. (2) Remove the overhead console retaining screws, located in the sunglass storage bin. (3) Using your fingertips, grasp the sides of the overhead console and pull straight down evenly to disengage the two snap clips at the front of the unit. (4) Lower the overhead console far enough to access the wire harness connectors. (5) Disconnect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (6) Remove the overhead console from the vehicle. INSTALLATION (1) Position the overhead console in the vehicle. (2) Connect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (3) Grasp the sides of the overhead console and push straight up evenly to engage the two snap clips at the rear of the unit. (4) Install the overhead console retaining screw, located in the front of console. Torque the screw to 1.2 N·m (10 in. lbs.). (5) Connect the negative battery cable.
Check engine light and an improper reading in the overhead console.Check engine light and an improper reading in the overhead console.
The dimmers control the intensity of the lights.