0
only misses on left side have tried everthing new knifes set timing still misses
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you adjust ford 530 hay bailer knotter and needles?
No need to answer I've just got the book for the baler and have made correcting adjustments....... Thank you............
Is Ford 3000 tractor pressure plate 3 or 4 finger pressure plate?
3 finger on early models
How do you thread a ford 532 wire hay baler?
Run the twine out of the twine box and through the guide next to the needle. Then run the twine through the needles and tie it off somewhere. When the knotter trips, it will inject the twine into the knotters and it will be threaded. If your baler has been sitting for awhile, it might take a few cycles for it to start knotting properly due to rust. for starters if it's a wire baler it doesn't have twine or knotters; it has wire and twisters. but it's true you thread it through the guide holes in balewire box, down through the sheaves, up over sheaves just before the needles and across the top of the needles then tie it off to the brace just like a twine baler. be careful, make sure it's centered over the top of the needles. after it makes a cycle you should be able to see if it picked up the wire and has held it in twisting grippers. it is held in these until the wire goes around the bale, then it should twisted and cut. make sure sheaves that wire goes through are lubricated with wd40 or something similar. i bought my 532 about five years ago and it does a good job. i think you can still get a manual for this baler from your ford ag dealer.
How do you check the manual transmission fluid in a 2001 Ford Escape?
on the bottom of the transmission there is a plug that you take out. you can stick your little finger in the hole where the plug was to see if it is low. if you do not get fluid on your finger, it may need a quart or so.
What is the torque specification for spark plugs on a ford f-250?
When the plugs are finger tight, tighten them with a ratchet 1/16 of a turn.
How do you thread a Ford 542 hay baler?
fisrt you need to get a ford baler I recomend looking at aution fliers in the Midwest [much more time comsumeing then eBay] If this step takes long enough you may never have to make hay just keep going to auctions. Once you have the baler you will need to have a tractor to power it I recomend inheriting one from your gampa or pa if this is not possible you will probably have to borrow one, as a last resort buy one . Next make sure you have twine loaded in the twine bin wich is located at the rear of the baler [the door that opens up] you will need two bales rolls of twine one for each side of the bale. As you stand behind this compartment look to the lower left side you will see two clamps held in place with a wingnut over a tensioner spring behind this is the hole the twine goes thru loop the twine thru the loosened tensioner and let it fall through the hole so it hangs below the compartment towards the ground. At this point it helps to have a partner I recomend having one of your children help you, that way they will know how to thread a ford baler it will also give them the chance to increase their vocbulary of words not to us in school. If you don't have a helper don't give up! Crawl under the baler [wait] befor you can finish this the baler has to be hooked up to the tractor draw bar and the PTO shaft needs to be hooked up be sure all guards are in place. Now slide gently under the twine compartment to where you have pushed the twine thru the hole pull out 3 or 4 feet of twine you partner at this time should make sure the twine doesn,t tangle uo in the compartment front hole is for left side of bale rear whole is for right side , also when you put the spools of twine in be sure the twine spools out the center and up thru the top of the spool. If as you lay under the baler pulling out the twine thru these holes it should come out freely if it doesn,t tell the kid to give you some slack. Now as you look to the left side of the baler you will see two arch shaped thick pieces of steel called the needles depending on wich part of the rotation the baler stoped moveing at you mabe able to see the front part of them for as the baler cycles they will come all the way free of the bottom of the baler if you can see the front of the needles you will notice a hole in the front of each if the front of the needles are not visible you will need to cycle the baler by turning the flywheel do this manualy and have the kid watch and tell you when the front of the needles come free of the bottom of the baler now thread the twine thru the whole in the front of the needles left twine for left side right for right pull several feet of twine thru and let it lay on the ground, Now if you don't have a windrow of hay ready to bale this process cannot be completed if you do however you may tighten up the wingnuts over the tensioner springs until the twine pulls free but without free spooling it does need some tension. The baler now needs to be brought up to the windrow of hay and engauged let it start making a bale the first one wont tie but it will bring the twine up to the knotter wich are on top of the bale compressing area opposite the bottom where the needles are basically at this point if all is working correctly the second bale will tie perfectly as the needles feed the twine the knotters wich self feed . Then you are done if the second bale doent tie sqirt some wd40 on the knotters and adjust the bale knotter timing so you are making very small bales and run thru a fairly good piece of windrow even if it doesnt tie correctly rite away keep going for a while it may loosen up a stuck knotter and start working . be sure you gease all the zerk before you start
Why does JJ Ford's finger stop at the top of the list of detectives in the yellow pages in the Westing Game?
JJ Ford's finger stops at the top of the list of detectives in the yellow pages because she realizes that she is the most qualified detective for the job and is confident in her abilities to solve the Westing mystery. This moment symbolizes her determination and self-assurance in tackling the case.
Should you be able to press the timing chain tensioner with the finger on a 4.6 1998 Ford pickup?
If the cover is off and yess it should be tight on the drivers side as the crankshaft is turning the camshaft.
Why was grace sure that she was the only the heir How did she treat judge ford?
Grace believed she was the only heir because her inheritance was clearly outlined in her father's will. She treated Judge Ford with condescension and arrogance due to her belief that the inheritance was rightfully hers, leading her to dismiss and disrespect the judge.
How do you replace the antenna on a 2000 Ford Ranger?
first pull out the radio and undo the antenna plug from the back of it. Tie a 6 foot peice of bailer twine or similar string to the end above the plug, and tape it on. Next undo the screws in the plate holding the antenna to the fender of the truck( if that is the type you have). Pull the antenna wire out until you get about 6 inches of the string. Tie the string to the plug on the new antenna and tape it on. Go back into the cab and pull the string until you can get the plug. Pull the plug until you can plug it into the radio. Reinstall the radio. Go back to the fender and feed the rest of the antenna wire into the hole and put the screws back through the plate to hold the new antenna in place. If it doesn't have screws and plate, then the antenna is held on by a nut under the fender, and you need to undo the wheel well liner to get at it. good luck.
How do you reset the fuel cut off switch on a 1993 ford Escort?
Try in one of the kick panels inside the car. Think you will find a hole to put your finger in to reset it.Hope this helps
How do you check the trans fluid in a 1993 ford ranger splash manual?
I believe on the drivers side of the manual trans there will be two fill plugs the top one is the fill plug. if you stick your finger in the hole a little bit you should get fluid on your finger. its a rather big bolt head if i remember correctly. its about midway up the trans.
