answersLogoWhite

0


Best Answer
Copy

Try taking out the glovebox, and reach around to the left..there's a bracket mounted to the back of the stereo,should be one nut threaded onto a bolt coming out the back of the stereo. It's not fun to get to,so be prepared to get scratched up and use lots of foul language! You will probably have to go to Radioshack or Bestbuy and get a conversion wiring kit. Kev

User Avatar

Wiki User

βˆ™ 2006-08-02 19:42:22
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you remove tail light box in jeep wrangler?

Remove the lens, and the mounting screws are at the back of the box.


How do you remove a Jeep Wrangler tail light assembly?

take the four screws of that hold on the lens cover and remove it. if you look inside there will be 3 torks screws. remove those. and that's it.


How do you remove center console 99 wrangler?

Screws in the bottom hold it onto the floor.


How do you remove vent cover on 1997 wrangler?

There are screws in between the slats of the vent cover.


How do you remove dash bezel 2004 jeep wrangler?

remove the top dash panel closest to the windshield, then remove mounting screws for dash module.


How do you replace the license plate lights on a 87 celica convertable?

There are two screws on each side holding the light pods. Unscrew the screws and lift out the pod, remove the bulb by undoing the screws inside holding the pod together...get bulb out by twisting from socket.


How do you change the wiper motor in a 1990 Jeep Wrangler?

you have to remove the panle on the outside of the jeep between the hood and the windshield. 4 screws.


How do you remove the console in a 1998 jeep wrangler in order to remove the carpet?

There are screws going through the bottom into the floor, should be about 6 in the front, middle, and back of the inside of the console.


How do you remove a 2003 Jeep Wrangler center console?

The previous answer was a bit of a dick answer. There are three screws. You have to pull out the front cup holder and remove that screw (might take some work as mine had some glue on the end of it). Then remove the rubber bottom of the back cup holder and remove those two screws (torx screws, so you have to have the right tool). After that, you can pull the console out.


Where is the oil pressure sending unit on a 1993 jeep wrangler?

Above the oil filter, where it screws on. You'll need a special socket to remove/install a new one.


How do you install the headlamp switch in a 1995 jeep wrangler?

I am pretty sure you have the toggle style switch, remove the lower dash bezel, and the switch is connected to the metal frame with 2 screws.


Where is the blower motor located on a right hand drive 2006 jeep wrangler?

It is located in the engine compartment, behind the battery. you have to remove the battery & computer (3screws) & 3 screws will detach it


How do you replace the console speaker on a 2001 Jeep Wrangler?

Remove the screws that fasten the console to the floor, there are 2 in the rear cupholder, 1 in the front cup holder, and 2 near the shifter (where the console seperates). When all the screws are removed you can lift out the console (be careful to unplug speaker wires), turn over, and remove the speaker.


How do you replace a camshaft sensor on a 1999 Tahoe?

The cam shaft position sensor is located under the distributor cap. You can replace this easily by undoing the screws holding on the distributor cap, remove and replace the sensor, then just replace the distributor cap.


Where is the O2 sensor on a 2000 jeep wrangler?

It's in the exhaust. It screws into the catalytic converter.


How do you install mirrors on a Jeep Wrangler?

They attach to the top door hinge with three screws


How do you remove glove box 2002 jeep grand Cherokee?

The 2002 Jeep Grand Cherokee glovebox is secured with a retaining screws. There are four retaining screws on the top and for retaining screws on the bottom of the glovebox. Remove the retaining screws to remove the glovebox.


Where is located the fuse box on a cougar 99?

One in the engine compartment just near the battery but the one you are probably after is behind the glovebox. You need to partially remove the glovebox by undoing its fixing screws; it will then hinge down allowing access to the fuse panel.


How to change a 96 Camero headlight?

remove the torx head retaining screws and remove the bezel. remove retainer screws but dont touch the adjustment screws and pull out headlight then unplug . replace light, plug it in and secure it. then replace bezel and its retaining screws.


How do you remove the front seats of a 1995 jeep wrangler?

On the underside of the track on each end there is a torx screw. Slide the seat forward and you can get to two of the torx screws. Slide it back and you can get to the other two. The seat will lift off without having to remove the brackets.


Where is the relay switch on a transporter van?

On t25 vans! After disconnecting the battery drop the fuse holder by undoing a couple of screws. the relay is on the back of it!


How do you replace a heater resistor on a jeep wrangler?

heater resistor will be located in the upper section of the plastic trunking for the air flow from the cowl grill. It should have 3 prongs fitted for the wiring and normally 2 screws to hold it in place. Remove the screws and the resistor should pull right out.


How do you remove front speakers in a Mitsuibishi Mirage?

Remove the speaker covers, by loosening the retaining screws. Remove the speaker retaining screws. Remove the wiring harness. The speakers will come out.


How to do you install the passenger mirror on a 98 Dodge Stratus?

remove door panel then remove screws behind mirror. remove door panel then remove screws behind mirror.


How do you get to the 3rd brake light of your Astra mk4 to attach a chrome A S T R A sticker?

Need to remove the tailgate inner trim panel on hatch and estate car.The lamp is held on by two clips (estate)or two screws(hatch)the wiring needs a couple of ties undoing to remove the lamp.