Windows and Mirrors
Chevy Silverado
Chevy S-10
Ford Explorer XLT

Can you replace the mirror glass only on Chevy S-10pickup side mirror instead of entire housing?

282930

Top Answer
User Avatar
Wiki User
2015-07-14 15:07:25
2015-07-14 15:07:25

You should be able to I have a 87 Chevy celebrity and I found just the glass at an auto parts store they have a section with just the mirrors and on the back of the mirrors it tells you which vehicle it is for. you.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You can replace just the glass on your RAV4 instead of the entire mirror housing. We have them available starting $19.99 depending on which side you need. Thanks Jack

User Avatar

go to parts house or yard ( save $100 ) replace entire housing

User Avatar

You don't. Instead, you replace the entire assembly.

User Avatar

To replace the brake light first you need to remove the lens housing from the car. Next pull the entire bulb assembly, or housing, out of its hole. Remove the bad bulb, replace with the good bulb and place lens housing back into position. Secure the housing with the screws.

User Avatar

you must pull out the entire breather assembly, then you unscrew the housing. Next, flip the retaining clip and replace the radiator.

User Avatar

Open trunk, locate the 2 small nuts that are located behind the light housing. Unscrew the nuts, then wiggle the entire housing away from the car. then you can get at the back of the housing to remove the bulb.

User Avatar

The CKP looks like a small gear with long teeth located inside the distributor housing. If the CKP fails, unfortunately you must replace the entire distributor housing.

User Avatar

Open the trunk. On the side of the lamp housing facing the trunk there are two 6pt screws. Remove these two screws and you will be able to grab hold of the lamp housing (the entire tail light assembly) and slide it out towards the rear of the car. Now you can access the bulbs from the rear of the lamp housing. Just received letter for recall to replace entire tail light assembly. Check with dealer to see if your car is covered.

User Avatar

Open the trunk and there should be several small bolts or wing nuts that can be removed. Then the entire center housing can be removed, twist the old bulbs out and replace.

User Avatar

Front of the engine block on left side, below the alternator. If you replace thermostat, it is easier to replace entire housing. When you purchase one it will all come as one unit.

User Avatar

Unlike other cars, the Intrepid requires you to remove the entire headlight housing. This is very simple, there are to long bolts on top of the housing that hold the housing on. Simply remove these bolts, untwist the bulb, replace the bulb.

User Avatar

The transmission housing for a 1991 E350 is bolted to the rear of the engine. The entire transmission case is considered the housing.

User Avatar

Subaru Forester does not have cornering lights, so chances are you are asking about the front parking light. The housing is held on by one screw accessible under the hood. You then pull the housing toward the front of the car. Bottom of that housing has a ball stud that fits in a socket on a small ear on the headlamp housing. This will allow you to either change the bulb or change the entire housing. --Ken

User Avatar

On older vehicles you replace the entire headlight. On the newer vehicles you just replace the bulb unless the headlight assembly is damaged.

User Avatar

Gear is part of the outboard CV jount housing and is not separately replaceable. Geberally entire shaft known as halfshaft is replaced.

User Avatar

As you look at the engine from the front of the car, the thermostat is inside a housing located on the front of the engine on the left side. There is a large hose and a small hose that come off of the housing and two bolts that hold it to the engine. You must replace the entire housing and it costs about $45, but it's a simple job.

User Avatar

It is in the HVAC housing under the instrument cluster. The entire dash, and the HVAC housing will have to be removed.

User Avatar

The owner's manual shows that there are two screws on the top of the headlamp housing that hold the entire housing to the vehicle. Remove those two screws and then you have to slide the entire assembly out towards the front of the vehicle. This is the hard part as there is a clip that the bottom of the housing slides under that holds it down and you must slide the housing straight back to get it out. It's difficult because the housing is flush with the grill and body work so there isn't much room to grab. Just be patient and don't force anyting as it's all plastic. Once you've removed the assembly, unplug it from the vehicle wiring harness and then take the whole thing inside to work on. - Remove the rubber boot covering the lamp that needs replaced - Remove the wiring connector - Remove the metal retaining clip by turning counter clockwise... two small tabs on the clip slide under the two torx screws which holds the lamp in place. - Replace old bulb with new one being careful NOT TO TOUCH THE GLASS PORTION OF THE BULB. - Replace clip. This took the longest for me as I have big hands and had to do the whole thing using tools instead of reaching into the housing and doing it all by hand. You'll need a helper to level the housing while you work on the clip. - Replace wiring connector. *** Test the lighting now before reassembling everything in case you have a bad bulb or connection. *** - Replace rubber boot. - Reconnect to vehicle wiring harness - Slide housing straight back into vehicle, making sure the lower portion of the housing slides under the retainer in the bottom of the opening. - Replace screws

User Avatar

No. You will have to remove the shift knob and center console and part of the lower dash in order to access the heater core housing. Be careful not to damage the housing when removing it; there are some screws in the front which are difficult to see and access.

User Avatar

Desconnect the cable on the carbrrator. On the accelerator pedal, twist the bent offset on the cable out of the side of the accelerator pedal and pull the cable out of the housing. Push the new cable into the housing at the pedal and install the offset into the pedal. Be sure the cable has gone through the entire cable housing, including the one through the fan housing. Connect to carb.... Now, wasn't that easy?

User Avatar

Jehovah's Witnesses. They use the entire Bible.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.