0
Not all crankshaft pulley bolts are left hand thread. In my experience if it is a left hand thread the bolt head normally has an L stamped on it to notify the direction of thread
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you remove 1997 Avalon crank shaft pulley?
remove 22mm center bolt its regular thread there are 2 threaded holes in pulley you will need the right pulley remover with the right bolts for the pulley you can get this at most parts stores make sure to not mess up crankshaft bolt threads
Where is the crankshaft speed fluctuation sensor on a 1999 Honda civic ex?
it is located behind the timing belt cover at the bottom half. you will need to remove the belts, crank pulley (reverse threads) and the attaching bolts to the plastic cover. it is the only sensor located next to the crankshaft it self. two wires one blue and one white. goodluck.
How do you repair a crankshaft pulley for a 98 Saturn SC2 DOHC?
u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removalAnsweru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answeru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal
Where can you locate the crankshaft on a 1988 Pontiac firebird?
open the hood the very bottom pulley at the center of the engine bolts to the crankshaft
Which direction does a crankshaft pulley bolt come of on a 95 Honda accord?
crankshaft pulley bolt is left hand thread,so it will come out opposite direction to normal bolts
Are the oil pan bolts reverse threads or regular?
They're typically regular thread.
What direction do you turn the bolt on the crankshaft pulley to remove it?
Most crankshaft pully bolts on European engines turn anti clockwise to undo them.
Are the blade bolts reverse threads on a John Deere deck?
If the grass exits the right side of the deck, then the threads are normal right handed treads. If the grass exits the lefts side of the deck, then the bolts thread are left handed threads.
You have removed the crankshaft pulley nut but pulley will not come off?
You may need a pulley (aka gear) puller to pull it off of the crank. The puller comes usually with bolts or claws you can ancor onto the pulley...
Are the threads on the bolt for the crankshaft pulley Left hand or right hand threads?
Toyota 4runner 1999 has right hand threads. I used a flush gear puller (washered out between the puller halfves to allow alignment of two drill bits into holes in crankshaft pulley and also allows enough room for 19mm socket to be used on crankshaft pulley bolt, I then used a deep socket over one of the puller bolts (nut end) with a couple of extentions wedged against the truck frame ) then with a half inch drive breaker bar and a four foot cheater pipe was able to break the torque on the nut. However the bolt on my gear puller will have to be replaced (bent), but I didn't have to purchase or manufactured any special holding tool.
Where is the crankshaft on 1997 Chevy 350 sub?
It is bolted in the bottom of the engine block and runs the hole length of the engine from front to rear. The flywheel bolts to the rear of the crankshaft and the bottom front pulley on the engine bolts to it also.
Remove Taurus harmonic balancer?
Remove belt,4 pulley bolts and remove pulley. Remove harmonic balancer bolt and washer,reinstall bolt with out washer,just in about half way.You will need a harmonic balancer puller.These are not very expensive about $20.00 or borrow one from somebody.You just thread the correct included bolts into the balancer where you removed the pulley bolts and will be pushing on the reinstalled balancer bolt.The balancer should clear the bolt head without the washer.This is so you don't damage the threads in the crankshaft.
