0
Does a 2000 5.3 liter vortec have a keyway for the harmonic balancer or is it just pressed on and held by the new stretch bolt?
Wiki User
∙ 13y ago
it has a key in it.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Is the keyway on a small block Chevy at 0 degrees?
This is a good question. Yes, the keyway, is accurate. What is not, is the balancer. After 74, the balancer keyway is offset, from the timing mark. Any harmonic balancer you use, look to see where the keyway is, compared to the hash mark on it. Make sure they line up.
Can a harmonic balancer have the wrong keyway?
A replacement balancer could have a wrong keyway. The vehicle could be a half year, meaning that the balancer is listed for one year newer or older vehicle, or the balancer could have been made wrong.
How do you change a harmonic balancer on a 1999 Jeep Cherokee 4.0 L?
Remove the belt. Remove the bolt that attaches the harmonic balancer. Rent or purchase a harmonic balancer puller. Follow the Instructions with the puller and remove the old balancer. Install the new balancer making sure to line up the keyway, a little oil helps. Put the retaining bolt back in and tighten to manufacture specs.
Where is the cam position sensor located on a 1997 350?
CRANK KEYS There is no keyway in the hub for the harmonic balancer, so GM used a special cutback key that was flush with the front of the timing gear on the 1992-
96 Chrysler Cirrus LX 2.5 Harmonic balancer fell off. Auto store says it's still good. I'm trying to put it back on but need a pin but don't know what it's called. Need instructions and pin name.?
The "pin" you are referring to is a keyway bar (probably also called keyway pin). You will need to know the dimensions of the keyway slot on the end of the crankshaft (or perhaps your auto parts store can find it in their computer). If I am not mistaken, the bolt or nut that holds the harmonic balancer to the cranckshaft has a left-handed thread (you can check at the auto parts store).
How do you install a harmonic balancer in a 1977 Lincoln Continental?
take off the old one with a harmonic ballencer puller you can rent one at the tool rental store, there is a large screw holding the ballancer in place with a keyway, you losen the screw tell its almost off but not all the way and then you attach the puller to the ballencer with two screws then you turn the center screw in until the ballancer pops off ..
Is the crank bolt on the harmonic balancer of a Toyota 4 runner left or right hand threaded?
It is standard thread. Torque to 220 ft lbs. Apparently the keyway is deep inside barely protruding from the timing gear on the crank so you might have to push that gear back to figure out where to line it up. I have not confirmed that yet though since my balancer just fell off last night.
How do you take of a harmonic balancer on 94 jeep wrangler 6cyl?
some wut of an Answeryou take off the center bolt then you rent/buy a harmonic dampener puller/installer and screw the three 3/8 bolts into the harmonic balancers body and pull it off by turning the center stud wich seperates the balancer from the crankshaft. and follow the same steps for re-installation now you are pressing the new balancer on the crank make sure the keyway on the shaft and the pulley are aligned or its gonna cost you a new crankshaft and if you replace the crankshaft might as well re-build the engine. It's obvious that before any thing you have to remove your belt/fanclutch and fan/ fan shrowd or you will not have any room to work.94 grand Cherokee Laredo 4.0berto
Can you weld a crankshaft in a big block Chevy the balancer came loose and distorted the keyway I want to TIG the key to the shaft in its original position and bolt on the new balancer Can this b done?
Yes , it can be done by a good welder
When your 1991 gxl rx7 rpms go up it vibrates why?
not really sure could be fly wheel or counter balancer out of alignment (broken keyway)
Install the harmonic balancer on 1999 Chrysler Town and Country?
how do use a harmonic balancer puller on my 1993 town n country chrysler Remove lower pulley-on balancer, should be 3 bolts & any accessories, etc. in the way. Remove center crank bolt with breaker bar or impact wrench. Thread puller into end of crank where center bolt was. Thread bolts thru 3 ears where puley bolts were or if you have the one with 3 "claws" clip them over sides of balancer. Slowly turn turn to pull off end of crank as is pressed on. Be careful as eventually it will pop off. Use one that is good quality so you don't damage threads in crank & thread it in there good. There is an install tool as well that uses center threads to press on & you can feel when it seats. (There is a keyway so timing mark will line up right. In a pinch can install with an impact wrench or tap on with wood & mallet, but have to be careful about threads or damaging bearings that way.
When was Keyway Air Transport created?
Keyway Air Transport was created in 1986.
