answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2008-04-19 00:25:56

broken motor mount(s)

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

What would cause your car to make a grinding sound while traveling at speeds under 35 mph?

Are we talking about the front wheels or the rear? Have you checked your wheel bearings?


How do you know when to get your brakes checked?

If you suspect something, get them checked. If you get vibration while applying the brakes, get them checked. If you get grinding noise from the brakes, get them checked.


Why does 2000 Impala shake at 50 tires good had checked?

Have the wheel bearings checked, as well as the alignment.


What would cause a loud grinding noise when brakes are applied had brakes checked are fine happens in reverse and starting out sometimes?

only thing i know that will make brkes grind, is worn out brakesmaybe have em checked at a different mechanic


How often the front wheel bearings should be checked?

With each brake job.


What is making a grinding sound on the rear of your 300 Honda 4x4?

It might be the clutch but get it checked out


What would cause a terrible grinding noise from the front wheel drive on a 1995 Oldsmobile Cutlass Supreme?

It could be a few things hub bearings, brakes, ball joints or possibly the CV axle. I would have it checked and then fix the problem at home if it is within your ability.


Today driving home my 1996 jeep Cherokee started making a grinding sort of sound from the driver side front wheel. I think it might be the bearings but not sure. Any ideas?

yes sounds like a wheelbearing get it checked before it tears up your spindle


My brakes are making a grinding noise what does that mean?

Check or have them checked immediatley. They are going to fail REAL soon.


What causes Right front tire area to make deep grinding sound making an extreme righ turn?

Have your brakes checked, rust or wear on brakes can cause grinding when turning.


What is the grinding noise when car is in full left lock?

Most likely the C.V. joint needs replacing. The grinding noise is usually a sort of clicking sensation. Another problem you might have is similar the the problem i had with my clio. when i put the steering on full lock i could hear a grinding noise. the thing i did was have my car checked by a garage and they found that the suspension had shattered. you need to get it checked.


What is the grinding noise when switching gears from drive to reverse somewhere in the rear tires that is only heard when starting the car for the first time each day?

Probably a problem with the transmission "valve body". Have it checked out with a transmission specialist.


What would cause a squealing sound from passenger side of a 2000 crown Victoria?

Have u checked the bearings?


What is causing a grinding sound on hard right turns?

Most probably the driveshaft(s) or the axles are worn. Get them checked.


What is the grinding noise that your car makes when you step on the brakes?

Have you checked the pads to make sure they are still ok? my first car made a horrible noise when i used the brakes and it turned out the pads were bald so it was metal on metal. Only other thing i can think off is that the wheel bearings on their last legs?


What is the grinding noise from the fan under the hood in front of the motor?

grinding noise from the fan is a bad bearing on either the fan or the water pump.have it checked before it lets go and goes thru radiator


How do you fix the bearings on a 2002 pt cruiser?

If the engine bearings are bad, then the oil pan will need to be removed to gain access. The engine will probably need to be removed and checked for other damage, as bad bearings can score the crankshaft requiring it to be turned smooth or replaced.


What does port and polish mean?

Port and polish is grinding to improve the flow of the cylinder heads. After grinding and polishing the intake and exhaust ports , a cylinders air flow capacity is checked with a flow bench. Further grinding is done to match all ports to the same flow rate.


How can you tell when your wheel bearings need replacing?

You can tell when your wheel bearings need replacing is when they are making unusual noises. For example: squealing, groaning, chirping or cracking noises. If this happens, get it checked out right away.


What is wrong with your 2002 Monte Carlo when its making a loud humming noise the faster it goes?

need to get your wheel bearings checked


Why is your Lincoln Mark 7 1985 making metal clashing sounds and front wheels vibrates?

Have the wheel bearings checked.


What causes a 2000 merc mountainer 5.0 liter 2wd to growl in right front and increase with speed?

Have the front hub bearings checked. Had a similar issue with a 2004 and it was the bearings which are not very good in this model anyway.


How do you Prolong the Life of Grinding Mills?

First of all, during the operation of grinding mills, there should be specialized staff responsible for guarding the machines, and the operating staff must have the good technical level. Before the installation of grinding mills, it is necessary to conduct technical training for the operating staff. Moreover, it is necessary to reserve some maintenance tools and grease accessories. Next, grinding mills should be examined and repaird after using a period, and the quick-wear parts such as grinding roll, grinding ring and scraper knife should be repaired and replaced. The bolts and nuts should be checked carefully before or after the use of grinding roll device. When replacing grinding roll after using for more than 500 hours or so, it is necessary to clean various rolling bearings and replace quick-wear parts. As to the fueling tool, manual refueling or grease gun is a good choice. Finally, grinding mills should be operated in strict accordance with the instructions. If the equipment breaks down halfway, it can't be modified at random but should be maintained by professionals and technicians.


Volvo XC90 inside front tires are wearingWhat should I have done to correct?

You need to havealignment checked or maybe wheel bearings worn


Does the front and rear wheel bearings on a 2000 Ford Ranger 4X4 need repacking or are they internally lubed?

They need to be checked, cleaned and repacked.