Chevy Blazer S-10
Ford Explorer Eddie Bauer
Honda Civic DX

How do I replace the distrubutor cap on 2000 S-10 Blazer 6-cylinder 2 wd?

Top Answer
User Avatar
Wiki User
Answered 2006-12-31 21:30:38

Get The New One First. Remove The Cap From The Truck. Do Not Remove Wires Before Removing Cap. Unless You Install Them In New Cap Matching Together Making Sure They Are Positioned The Same. Locate a Clamp Or Indention On The New Cap That Matches The Old One. Start at This Point Remove The Wire From The Old Cap Put It Into The Same Place on the new one. Then Just Work Around Clockwise Removing The Next Wire In Order As You Removed The First. Then Install Coil Wire. HOPE YOU DON~T GET CONFUESSED. ++TAKE YOU TIME ALSO++

User Avatar

Your Answer

Still Have Questions?

Related Questions

How do you replace the front driver side seat belt on a 2000 Chevy Blazer?

how do you replace seatbelt retractor on a 2000 chevy blazer

How do you replace drive shaft 2000 Chevy Blazer?

I have a leak on my drive shaft left front 2000 cheve Blazer I would like to replace the whole unit

How do you replace headlights for a 2000 Chevy Blazer?

You get a pro to do it.duuuhhhh

How do you replace the heater core in a 2000 Trailblazer?

They did'NT make the Trailblazer in 2000 might you be looking for information for a 2000 Blazer.

How do you replace the headlight bulb located on a 2000 Chevy Blazer?

read the manual

How do you replace lower ball joints on a 2000 S10 blazer?

first you take it in then pay them to do them for you!!!!!!!!!!

Where and how do you replace a 4.3 olds bravada 2000 6cylinder fuel pump?

In the fuel tank. Remove the fuel tank & take fuel pump out from the top. This is NOT a job for an amateur.

How do you replace an ignition switch for a 2000 blazer?

To replace an ignition switch on a 2000 Chevy Blazer remove the lower steering column and dash. Locate the ignition switch and pull the end-clip off the main harness. Remove the mounting screws from the ignition cylinder and replace the unit.

Do you have to drop the tank on a 2000 Chevy blazer to replace the full pump?

Yes you do. There is no other way.

Can you cut through the firewall to replace the heater core in a 2000 Chevy blazer?

You can but you still won't be able to get it out.

How do you fix blower resistor on 2000 Chevy blazer s10?

Ain't no fixin it, you have to replace it with a new one.

What liter is a 2000 cavalier 2200 sfi-6cylinder?

In 2000, the Chevrolet Cavalier only came with two different four cylinder engines. The 2200 sfi, one of those engines, is a 2.2 litre OHV pushrod four cylinder.

How do you replace a rear brake line on 2000 Chevy blazer?

Length of back brake line to replace. hole in it between front and back door

Will an alternator from a 2000 Chevy blazer fit a 2002 s10 blazer?

An alternator from a 2000 Chevy blazer will fit a 2002 S10 blazer with a little fabrication.

Do you have to take the gas tank off to replace the fuel pump on a 2000 blazer?

YES you do. That's the only way.

What do you do before you replace a fuel pump Chevy 2000 S10 blazer?

Disconnect the negative battery cable from the battery.

Are hoods to a 2000 gmc jimmy compatible to fit a 2000 Chevy blazer?

Yes, a 2000 GMC Jimmy hood is compatible to a 2000 Chevy Blazer. This is only on the S10 Blazer though.

Does a 2000 Chevy Blazer have rear disc brakes?

Yes. I own a 2000 Chevy Blazer.

How how to set the timing on a 2000 Chevy Blazer?

How do you set the timing on a 2000 Chevy blazer (V6)

Will a 4.3 liter engine from a 2001 blazer fit a 2000 blazer?

It will as long as the 2000 had a 4.3L in it too.

How many coil packs does a 2000 Chevrolet Blazer have?

The 2000 Blazer with the 4.3 engine has one coil.

Why won't a 2000 blazer start in damp weather turns over but doesn't fire suggestions?

replace the spark plug wires

Is replacing the wheel bearing on a 2000 Chevy Blazer a do-it-yourself job?

Yes it can be. I think you need to replace the whole hub assembly

How do you replace the distributor drive gear on a 2000 Chevy blazer?

The distributor drive gear would be part of the camshaft. The camshaft would have to be replaced.

Will a 2000 s10 blazer rear bumper fit a 1996 blazeR?


Still have questions?