answersLogoWhite

0

  • Antifreeze and Engine Coolant
  • Radiators
  • Pontiac Firebird
  • Grand Prix GT

How do you bleed the air of a 1995 Pontiac Firebird coolant system?


Top Answer
User Avatar
Wiki User
Answered 2015-07-15 21:06:17

Find the thermostat housing. There should be an air bleeding screw located on the top side of the housing. As you add water to the radiator open the screw until water runs without the sign of air bubbles.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

How do you bleed the air out of the coolant system on a 1997 Pontiac Montana?

If it has bleeder valves then use them to bleed the system, if not, jack up the front of the vehicle as high as possible. Remove the radiator cap and start the engine. Add coolant to keep the system full. This will allow air to escape.


How do you bleed air out of coolant system 97 Saturn?

procedure on how to bleed air out of coolant system on 97 saturn ls


How do you bleed your V6 coolant system?

how do i bleed my accord v6 2000 coolant system, its has air and the rev's gone up & down......


Where is the place you bleed coolant system?

It is not necessary to bleed the coolant system. If you mean "drain" the system, there is usually a plastic plug on the radiator or, you can pull the lower radiator hose off.


How Do you Bleed The Coolant System On A 1998 Beetle?

To bleed the coolant system on a 1998 VW Beetle, remove the top from the overflow tank. Run the car for 10 to 15 minutes to force any air out of the system, then check the coolant level. Add coolant as needed.


How do you bleed the coolant system on a 2002 impala?

There is a bleed screw on the thermostat housing. Remove the screw with the engine loose. Ounc you have pure coolant and no air you can close off the bleed screw.


How do you replace the thermostat located on a 1991 Pontiac Bonneville 3800?

I believe you want to drain the coolant, remove the top hose at the thermostat housing, remove the housing, replace the stat and gasket, reassemble fill with coolant and bleed the system.


How do you Bleed the coolant system on a 2002 Chevrolet Impala?

There is a bleed screw on the thermostat housing. Remove the screw with the engine loose. Ounc you have pure coolant and no air you can close off the bleed screw.


How Do you Bleed The Coolant System On A 1998 2.0 Beetle?

Start by taking the top off of the coolant overflow reservoir. To bleed the system, run the 1998 VW 2.0 Beetle about 10 minutes, then check the coolant level. Add coolant if needed, then replace the reservoir top.


How do you bleed coolant system after replacing thermostat?

what is the year make & modle of it??


How do you bleed the coolant system on a 1999 mercury villager?

Not necessary on this vehicle.


How do you bleed my coolant system?

As you did not include engine or Year info I will give a general answer. Look on the top of the engine, most GM products with a bleed system have a small brass pipe thread plug in the top of a black or aluminum casting. This is the bleed point, loosen the plug or valve and add coolant to the system until it flows from the bleed, tighten up the bleed. Done. Repeat if needed.


How do you bleed cooling system on pontiac 2.4?

To bleed the cooling system on a Pontiac 2.4 engine, there is a small hose near the bottom of the radiator that needs to be removed. Then remove the radiator cap and the cap on the radiator overflow tank.


How do you bleed air from the cooling system of a Pontiac Grand Am?

It should be a bleeder screw connected to the cooling system, it might be two.If you find it,you should open one at a time.Pour coolant into the system slowly,until coolant start coming out of the bleeder screw and then close it . DO it to the second screw too.Now if you do not have the bleeder screws.Pour coolant into your system slowly and squeeze the top hose until no bubbles come out and the coolant level should go down at this time and then pour alittle more in there


Bleed 3800 engine cooling system?

Is the question how to bleed a Buick 3800 cooling system? I would say open that little petcock by the themostat housing and release all the air as you fill the system with coolant. When coolant comes out instead of air all the air is out.


How to bleed air from coolant system in a 3.5 Olds Aurora?

Good luck haha..


How do you bleed coolant at 1999 Subaru Forester?

You should not need to bleed coolant. Ever. If the coolant is filling up on its own the stuff in there is not coolant and you have a big problem.


Do you have to bleed cooling system on a 1989 ford probe after changing the thermostat?

If there is not bleed valve for the coolant you will have to do it manually. Fill the radiator up and start the car. After it warms up the coolant level will drop, refill it.


How do you bleed air out of a 1995 Intrepid 3.3 liter engine coolant system?

To bleed the coolant in a 1995 Dodge intrepid locate the drain plug on the underside of the radiator, un plug it and pour new coolant in the system. Close the plug and while the engine is running find the coolant pressure valve and loosen it to relieve pressure. When bubbles stop forming there is no longer air in the system.


Why after replacing the water pump on a 1996 Cherokee is there no heat?

Low coolant level or possibly air trapped in the system. Bleed the system and check the coolant level in the radiator not the reservoir.


Bleed power stearing pump Pontiac?

There is no need to bleed the system, just turn the wheels all the way to left and right a few times, it will bleed itself. That's how you do that.


If the low coolant light is on when you just replaced the radiator in a 1994 Pontiac Grand Am with a sealed radiator system what could be the problem?

There is a high probability that the system needs to be bled. As in bleed the air from the system. Just filling the system is not enough. You need to warm the engine to get the water flowing, then switch off and bleed the air out. Yes there is always some air and it gravitates to the highest point of the cooling system. I hope this helps


Bleed coolant system in cadillac 4.6?

There is no need to manually bleed the coolant system on a Northstar, the system is self bleeding. The small hose on the side of the overflow tank is the self-bleed line. If, by chance, this line is obstructed, then the air will be trapped & cause overheating problems. Be careful is the plastic nipple on the side of the overflow tank as it is very weak & cracks easily.


Is there a way to bleed a coolant line on a 1995 Pontiac grand am with a quad 4 motor?

The best way to bleed air in any car's cooling system is to elevate the front of car so rad cap is the highest point of vehicle. Then just simply leave cap off while motor idles. Add coolant as necessary over the course of 30 minutes.


Where is the coolant air bleed valve on 2000 Mercury Villager?

The Villager engine does not have a coolant bleed valve.