To change a license plate bulb for a 2002 Suburban, no tools are needed. Just reach up under the back bumper just behind the license plate light that needs changing. Grip the bulb holder and rotate it to release it from the slot. Once released, you can pull the wire with the bulb attached down below the bumper to see it fully. Once you see it, pull the bad bulb straight out of the holder, then push a new bulb back into the bulb holder. While you still have the wire suspended below the bumber, turn on the running lights to make sure the new bulb works. Once it does work successfully, push the wire back behind the bumper, put the bulb back in its slot, and rotate the bulb holder until it clicks back into place. And, you're done.
It is very easy to change the license plate light on an Oldsmobile Aurora. All you need to do is remove the license plate and look above where the plate was. There are bolts that are holding the light in. Unscrew the bolts and then replace the light.
how do you change the light bulb over the license plate on 2000 eclipse
how do you change the rear license plate light on a 1999 Buick Regal
how do u change the license plate light on a 2005 sienna
show please how change plate light on an 2007 nissan sentra
If your license plate light is out change the bulb in it, if you have taillights your fuse is good as the license plate light uses the same fuse as the taillights.
on the 2001 XZ3 I removed the license plate and used a flat head screw driver to slid the license plate light cover over and they "pop" out.
how to change 2005 equinox license plate light i removed the screws but it didn't release
How do I change the license plate bulb on a 1993 Lexus ES 300
How do you change the liscence plate light fuse
license plate light just pops out of the bumper with a screw driver.u can buy a new light at auto store or just change the light bulb
Open your trunk and find the wires that go to the bulb over the license plate. Twist the base to remove the light.
To change the license plate light on a 2002 Geo Tracker, remove the light lens with a small screwdriver. Take out the old bulb and replace with a new one. Tighten the screws on the light lens.
Pull it out, dont twist it.
what is the number for the fuse to change the rear license plate light. and is it the fuse box under the back seat or under the hood? The plate light is protected by the parking/tail light circuit.
this light is called the license plate light
The license plate light circuit is protected with the tail light circuit fuse.
To change the license plate light on a 1998 Chevy Cavalier, reach up under the bumper and remove the bulb over the license plate. Then put a new bulb in the socket. The bulb can also be accessed by removing the lens on the outside, but there are screws to remove first.
Gentely pop out small light from behind bumper. I believe it is a 194 bulb and it will pull straight out and just push the new one in.
Remove 1. Bolts retaining license plate lamp to bumper. 2. Socket from license plate lamp. 3. License plate lamp. 4. Bulb from socket. Install or Connect 1. New bulb to socket. 2. Socket to license plate lamp. 3. License plate lamp. 4. Bolts to retain license plate lamp to bumper.
how to change the license plate bulb onLook at the rear plate , then get on the ground so you can look up to the underside of the bumper, where the plate is. There are two Phillips screws the hold your plate light, remove both, pull down gently on the light, then turn it co you can see the rear and with both Hans turn the socket and pull, there you will find the bulb. change it and do the reverse to install.
They are located inside the trunk lid, underneath the felt lining. You need to unsnap and pull back the felt lining to access the bulbs for the license plate light.
The 2001 Toyota Camry license plate light fuse can be found in the fuse box. The license plate fuse will be labeled as the tail light fuse.