Buick LeSabre

How do you change harmonic balancer on 1991 buick lesabre?

001

Top Answer
User Avatar
Wiki User
Answered
2014-08-23 07:15:43
2014-08-23 07:15:43

The flywheel has to be held in place by a holding tool, Remove the mounting bolt, then use a balancer remover to pull the harmonic balancer.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


it is behind the harmonic balancer.


I tried to change the harmonic balancer of my biuck lesabre 1994, but i can't remove the old one, the bold in the center is very , very tight and i don't know the type of screw, right or left turn.


You will need special tools like: harmonic balancer puller, and impact wrench.


its behind the harmonic balancer attached by two bolts but you must first take off the balancer to get to it


the crankshaft sensor is located behind the harmonic balancer on the ft timing cover


The 2000 Buick Regal 3.8L Crankshaft Position Sensor is located behind the harmonic balancer pulley.


sounds like the rubber damper is worn on the harmonic balancer. if this is the case you will have to replace the harmonic balancer.


probably damaged the crank sensor, or the tangs on the harmonic balancer


You need a harmonic balancer puller, and a 1/2 in drive inpact wrench.


The Crank sensor in my 91 LeSarre Limited is behind the Harmonic balancer pulley....there are fins on the back of the pulley that line up with the sensor.


Its refered to as a harmonic balancer, and you have to have a special tool to remove it called (surprisingly) a harmonic balancer removal tool. The installation tool is a good heavy hammer and a block of wood. If you dont have access to this special puller, you can (and likely will) damage the harmonic balancer, so it would be best in that instance to take it to your local mechanic and ask him to take pull it off for you.


I usually use my impact wrench but if you don't have one you could put a socket and wratchet on it. Then tap it with a hammer to get it started maybe.


The Crankshaft Position Sensor is behind the crankshaft pulley (harmonic balancer). You will need a ½-inch drive breaker bar and appropriate socket.


How to change brake lines on a 1991 Buick Lesabre?



take off your harmonic balancer the answer is behind



to my knowledge it is located behind the harmonic balancer. You should be able to c the wires runing to it just to the right of the harmonic balancer. Now if you could help me with information on how to uninstall the harmonic balancer i would greatly appreciate it Thanks. To remove the harmonic balancer you have to buy or rent a harmonic bancer puller. The bolts required for yours may not be included. If not you will have to go to the hardware store and purchace them. You should use the 3 1/2 inch #8 1/4 inch bolt 3 required also buy 3 washers cost under 4 dollars.


Instructions for replacing radiator on 2000 Buick Lesabre custom


sounds like you broke the crank sensor that is mounted right behind the balancer.



Actually, you don't replace the sensor itself. The crazy thing is part of the harmonic balancer, and you have to replace the whole thing.


The crankshaft sensor is located behind the harmonic balacer. you will need a puller with special bolts to remove the balancer.



It is located behind the harmonic balancer on the front of the engine. You'll need a special puller to remove the balancer.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.