To do this you need to remove the speedo unit itself. First off remove the 3 screws that hold the speedo surround trim there are 3 along the top but you point your screwdriver towards the roof. If that makes sense... The surround is the bit with the Boot release button on it. Once you remove the screws prise the surround out gently, there is a couple of clips that keep it in place but they should pop off quite easily. Then you need to unplug the boot release. The surround removed you then need to undo two screws in each top corner. one over near where the boot release button was and one near the trip computer. There are two more at the bottom but may be hidden a little by the rubbery sheet that sits on top of the steering rack, peel this back a bit. Once all the screws are removed then you need to unplug the power to the dials. The plug has a locking arm, if you open the car door you can get your head round the steering wheel enough to see it. The arm needs to be pushed away from the dials and to the left this also releases the wiring block. Once you have done it a couple of times it really is a lot easier than it sounds. The dials are then free. You will then be able to access the bulbs. You might need a small pair of pliers to twist them out but again once they have been swapped they will probably be just as easy by hand. If you doo need to remove the circuit board you may need a Torx screwdriver, I use a number 2 bit from my set and undid the 2 small screws, then I unclipped the plastic clips from the outside and eased it apart. Not the front, clear plastic screen also unclips but you won't need to do this for bulb changing. Hope this helps, please email me westy_26 at hotmail dot com or westy_26 at Yahoo dot com.
B8,5d :)
you have to remove the cover of the dashboard to replace the light bulbs
Changing the instrument panel lights require removal of the dashboard. With the dashboard removed pull the gauge cluster out and take off the bulbs. Install the new bulbs.
u must unscrew spedo facia then you will see more screws there is two different sizes of bulbs
If you want to change the bulbs behind the speedo dial, then there are four screws, two at the top and two at the bottom of the dashboard dials. Then remove the cover rim that holds the dial and you should find again another four screws, two to the left and two to the right. Once you remove those, you should be able to pull the dial and you will see there are two cable connectors and the speedo meter cable sticking at the back. Carefully pull to the back the cables and speedo cable by pressing the holder pin. At this point you should have the speedo dial detached and at the back you should see the bulb connectors that you have to twist to the left and pull out. There are many of them so you might need to check if they light before you disconnect the cables.
This is a tedious job and static electricity can ruin the printed circuit. TAke it to a garage.
Remove ALL dashboard screwscarefuly remove the dashboard,andyou will see were the bulbs are located,replace any/and/or/allthe bulbs needed,and reverse theprocedure to reinstall ! That's it !
The dashboard lights on a 1997 Eagle Talon can be changed by reaching up into the dash to get to the bulbs. Another way is to remove the dashboard screws and remove the front of the instrument panel.
Citroen xsara Picasso dashboard light bulb is the bulb that's for the dashboard light climate control. The you tube web site gives you information as how to change the bulb.
What model of Corolla ? You have to take the dash board out and the bulbs can be removed and replaced from the back. The dashboard on the Corolla is not that difficult to take out, but you have to do it slowly and carefully.
Begin by removing the instrument panel cover from your 2002 Pontiac Montana. Take hold of the dashboard lightbulb, push in and turn at the same time. The dashboard lightbulb will come out. Reverse the process to install your new dashboard lightbulb.
you have to take off the cowl around the clocks, then the clocks just unclip from the dashboard (no wires or cables) and pop out the wasted bulb and replace with the new one. while your at it, why not put in coloured bulbs for the clocks, to pimp it a bit replacing is just as easy as taking the clocks out