how to change the windshield wiper motor in a 2000 jeep wrangler
Unbolt the roll bar from the windshield. Lower the windshield. At this point you can unbolt the motor and replace it.
The motor sits under the cowl at the base of the wiper arm.
Where is the wiper motor located on a 1989 jeep wrang ler
The wiper motor is mounted on the left inside of the windshield frame on the same bracket as the VIN. Fold down the windshield and is fully accessible.
It is under the wiper cowl. The painted piece in front of the windshield.
The 1988 Jeep windshield wiper motor is located on the firewall in the engine compartment. The wiper motor will be in the center of the firewall.
Remove the windshield wiper arm from the windshield wiper motor. Remove the wiring harness. Remove the retaining nut. Reverse the process to install the new windshield wiper motor.
The wiper motor is on the driver's side, behind the dash board. if you fold you front windshield down, that will expose your wiper motor.
The windshield needs to be folded into the down position to access the wiper motor. There are a couple cut-outs in the metal of the cowl that allows access to the wiper motor & linkage. There are release bolts on either side of the windshield & of course the top needs to be off.
Fuse or windshield wiper motor.
you have to remove the panle on the outside of the jeep between the hood and the windshield. 4 screws.
You can try Quadratec.com, Rockauto.com, or your local jeep dealer
Under the vin plate. fold the windshield forward.
You need to fold down the windshield. So undo the torque head screws on each side & fold forward carefully. The wiper motor sits right under the VIN plate on the windshield.
The metal panel between the hood and windshield is removed to service the wiper motor.
Your wiper arms that run from the wiper motor to the windshield wipers may be binding and need to be replaced
The windshield wiper motor is located just below the windshield wiper blades and is covered by a black panel.
http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is very informative video on how to remove and replace a windshield wiper motor)
Take the wiper arms off. Then undo your windshield so that it folds down onto hood. Remove the three screws holding the wiper motor on. disconnect the wiper drive link. remove the wire clip from bottom on the windshield frame. Take out the 4 screws on the bottom of windshield that hold on the seal. (they get in the way of pullin the motor out). Pull the motor and link out through the access hole. Pry the link off the motor pivot. Do not remove the crank arm adjusting nut though. That's it. Sounds way harder than it is.
One could purchase a windshield wiper motor at a retailer such as AdvanceAutoParts. Alternatively, one could also purchase a windshield wiper motor online on Amazon or AutoZone.
# Remove the windshield wiper arms # Remove the cowl cover # Disconnect the electrical connector from the wiper motor # Detach the wiper motor/linkage assembly from the cowl # Remove the wiper motor retaining bolts and remove the motor
* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor
The windshield wiper motor may have a short in it. The windshield wiper motor may not be grounded properly. Make sure the ground wire is tight and free of corrosion.
You get to drop you windshield...the wiper motor is under it. Unbolt the rollbars at the top of the windshield, then unbolt both brackets on each side of the dash. Carefully fold the windshield down on the hood. Then you'll see your wiper motor. I just did this yesterday on my 95 YJ. Try putting some PB Blaster/WD40 on all the bolts and letting it soak in. I had to make a trip to Fastenal for a few replacements.