Dodge Ram Van
Ford Ranger XLT
Late Model 1979-New Ford Mustangs
1982-1994 Chevy Cavaliers

How do you change wheel bearings on a 1990 cavalier?

293031

Top Answer
User Avatar
Wiki User
2015-07-15 21:41:43
2015-07-15 21:41:43

You have to take off the rotors and calipers to get to the bearing then you probably need a heat gun to soften up the bolts to take them off

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

What kind of bearings??Engine, wheel, trans,diff.?????

User Avatar

No sir, it is front wheel drive.

User Avatar

The front wheel bearings are sealed and are not greaseable.

User Avatar

you take off the hair and pink nails of the car

User Avatar

how do you change rear brakes on a 1990 Honda trx 300fwl

User Avatar

Same answer Go to DTAmotorsports and download you a free service manual. http://dta-motorsport.com

User Avatar

To release the 1990 Cavalier serpentine tension, use a socket and a ratchet. Put the socket on the bolt heat in the middle of the pulley wheel, and pull to one side, and the belt will be loosened to be able to be removed.

User Avatar

Your front bearings are sealed and are replaced only when they become noisy. A badly worn bearing will roar at speeds above 40mph and will change pitch somewhat as you change from lane to lane due to the side load that is placed on it. Tire noise (due to tires that need rotation) is sometimes mistaken for a worn bearing.

User Avatar

The transmission must be removed to change the flywheel.

User Avatar

Are the front driving components(A-arms)from a 1993 Cavalier compatable with a 1990 Cavalier?

User Avatar

jack up van with wheel in question off the ground try to move it side to side it should not move also spin the wheel and listen for a grinding noise you may need a stethascope to do this step

User Avatar

Pull the wheel, pull the caliper and the rotor comes right off. You may have to tap the back side of it to loosen it up.

User Avatar

Cavalier 1985-93 Top of Glove Compartment

User Avatar

The 1990 Cadillac Sedan DeVille is front wheel drive. The 1990 Cadillac Sedan DeVille is front wheel drive. The 1990 Cadillac Sedan DeVille is front wheel drive.

User Avatar

start by taking the wheel off then take off the caliper. After take the rotor off. Then there is a nut with a pin through it, take the pin out and undo the nut. Now the hub will come off and one bearing will come out. With a hamer and a punch drive out the other bearing and the grease seal. You should change the races as well(the serface the bearings ride on inside the hub. You will meed it buy wheel bearing grease and pack the new bearings with grease. You can never use enough grease the more the better. Repeat the process in reverse to reinstall. If you have any more Questions E-mail me at reese_koch@hotmail.com

User Avatar

have a mechanic that specializes in frontend work do it for you. more than a general tool set is required to complete the job.

User Avatar

Spin That Wheel was created in 1990.

User Avatar

The curb weight of the 1990 Chevrolet Cavalier base sedan is 2,444 pounds. The fuel tank holds 13.6 gallons, and it uses regular unleaded gas.

User Avatar

The firing order for a 1990 Chevy Cavalier 2.2 is 1-3-4-2. The number one cylinder is closest to the front of the engine.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.