answersLogoWhite
American Cars
Heater Cores and Blower Fans
Oldsmobile Regency
Ford Explorer XLT

How do you disconnect the heater on a 1982 Oldsmobile Regency Brougham?

232425

Top Answer
User Avatar
Wiki User
Answered
2007-05-13 01:59:34
2007-05-13 01:59:34

Disconnect both heater hoses from heater core and connect them together

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


please tell me how to remove the heater to get too the heater coil


It is at the rear of the intake manifold, follow the heater hose. there is a flow door under the dashboard with a cable connected is that the control or does the valve body at end of intake still control it?


under the passenger side behind glove box the is a panel you must remove be careful for wires remove panel to display heater core remove hoses from under hod and then pull heater core out from inside passenger side



You can find the 1993 Oldsmobile Cutlass block heater on the right hand side of the engine block. You can follow the block heater cord directly to the block heater.


Best to get the shop manual but basically: Reomove Heater hoses from engine block and drain. Remove glove box. Disconnect cables that connect to heater core. Disconnect heater core from firewall. Disconnect hoses from heater core. Pull heater core from under dash.


How do you change the heater core on a 1989 Oldsmobile Cutlass Ciera? or where can I get the Info on replaceing it


Disconnect the negative battery cable and drain the cooling system.Disconnect the heater hoses from the heater core inlet and outlet connections in the engine compartment.Allowing residual coolant from the heater core to drain. Cap the openings.Working inside the vehicle, remove the lower instrument panel sound insulator.Remove the heater floor outlet duct screws or clips and remove the duct.Remove the heater core cover by removing the attaching screws and clips.Remove the heater core cover.Remove the heater core retainers and remove the heater core.



How to replace a heater hose on a 2001 Oldsmobile silloute


how do you replace a heater core in a 91 Oldsmobile 98


May be a defective thermostat or heater core


Try the repair tips on the Autozone web site.


Depends on the vehicle and somtimes engine size. B Clear.



your heater coil is leaking.replace it



i need instructions on changing a heater core on a 1997 Oldsmobile achieva


Disconnect the negative battery cable, heater blower resistor wires and blower wires. Disconnect the heater core ground strap at the dash panel.Drain the cooling system and then disconnect both heater hoses at the heater.Remove the seven screws attaching the heater/blower case to the plenum and remove the heater/blower base.Remove the four screws from the heater core shroud, and then remove the shroud and core assembly.Separate the core from the shroud by removing the three screws and core mounting clamps and then separating the two.


Disconnect the inlet and outlet hoses to the heater and couple them together Or, if the hoses are the same size, remove one completely, and disconnect the other from the heater core, then connect it to the other engine outlet (or inlet, as the case may be).


# Disconnect the negative battery cable. # Drain and recycle the engine coolant. # Disconnect the heater core hoses using tool J-37097 or equivalent. # Remove the right side sound insulator and the glove box module. # Remove the programmer shield, if equipped, and disconnect the air mix valve link. # Disconnect the programmer vacuum and electrical connectors. # Remove the heater core cover, leaving the programmer attached. # Remove the heater core retaining screws and the heater core.


Disconnect the negative battery cable.Drain and recycle the engine coolant.Disconnect the heater core hoses using tool J-37097 or equivalent.Remove the right side sound insulator and the glove box module.Remove the programmer shield, if equipped, and disconnect the air mix valve link.Disconnect the programmer vacuum and electrical connectors.Remove the heater core cover, leaving the programmer attached.Remove the heater core retaining screws and the heater core.



By the firewall, up and under the dash.


You have to pull the dash and all the lower fascia, then remove the box that houses the heater core. Take the clamps off the heater hoses from the engine compartment side of the firewall and disconnect the heater hoses. Disconnect the bracket that holds the heater core in place from the inside of the passenger compartment (if present.) Carefully remove the heater core and discard it. Install a new heater core reversing the above steps.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.