answersLogoWhite
Ford Ranger
Ford Expedition XLT
Ford Ranger XLT

How do you find and clean an IAC valve on a 93 ford ranger 30 L?

171819

Top Answer

User Avatar
Wiki User
2005-11-16 00:53:14
2005-11-16 00:53:14

the iac is on the throttle body. take the cover off of the throttle body to get to it theres 2 screws to take out for it to come off. clean off the old gasket be careful not to damage the gasket mating. and they recomend that you not use any solvent on them

1

Related Questions

User Avatar

egr valve location on a 1997 ford ranger 23l

User Avatar

200 ford ranger tappet valve clearance

User Avatar

There is a heater control valve on the 1999 Ford Ranger. There is no thermal vacuum valve on this year of the vehicle.

User Avatar

The PCV valve, on your Ford Ranger 2.5 liter engine, is located on the outside of the air cleaner housing. The valve is on the back of the housing.

User Avatar

The Idle Air Control (IAC) valve is mounted on the throttle body

User Avatar

The bleeder valve for the brakes on a 1997 Ford Ranger is located in the brake line where it meets the brake disc. The wheel will have to be removed to access the bleeder screw for drum brakes.

User Avatar

The 1993 Ford Ranger air conditioning charge valve can be found on the top of the air conditioning compressor. The charge valve will be marked as the low pressure valve.

User Avatar

where is the PVC valve located on a 1990 ford ranger 2.3 L

User Avatar

Look on the back of your valve cover and you should find it.

User Avatar

Begin by removing the cover to your 1993 Ford Ranger valve cover. Remove the gasket and clean the surface. Put the new gasket on and return the elf cover to its original position.

User Avatar

To clean the inside headlight lens on a ford ranger just simply remove the cap and clean.

User Avatar

what are the specification of valve adjustment for 2000 ford ranger wl inlet

User Avatar

its in the valve cover by the brake booster

User Avatar

On a 1997 Ford Ranger , 4.0 EFI engine : The PCV valve is on the top of the drivers side engine valve cover , near the rear

User Avatar

On a 1996 Ford Ranger , 4.0 : The PCV valve is on top of the drivers side engine valve cover , near the rear of the valve cover

User Avatar

The engines in a 1993 Ford Ranger are fuel injected , so there is no carburetor

User Avatar

The 1995 Ford Ranger 3.0 liter engine PCV valve can be found on the top of the engine. The PCV valve will be on the back side of the air cleaner.

User Avatar

The 1999 Ford Ranger low pressure air conditioning valve can be found on the air conditioning compressor. The low pressure valve will be labeled as the low pressure port.

User Avatar

On 2002 Ranger 3.0L, the PCV valve is mounted in the valve cover near the brake booster.

User Avatar

On 3.0L and 4.0L engines, the PCV valve is mounted in the valve cover near the brake booster. - Haynes Repair Manual #36071 - 1993-2005 Ford Ranger Pickups.

User Avatar

Hey Vince==It is in the valve cover. GoodluckJoe

User Avatar

On a 2000 Ford Ranger , 4.0 liter EFI , V6 engine : The PCV valve is on top of the drivers side engine valve cover It is near the rear of the valve cover ( towards the firewall end )

User Avatar

On your 1989 Ford Ranger : The vacuum modulator valve is on the passenger side of the A4LD automatic transmission ( it might be behind a heat shield )


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.