I a 97 pick up and the Power Steering pully is pressed on and pressed off
There are a few ways to set the timing on a 1994 Suburban 1500. Disconnect the connector firewall to loosen the distributor turning just a bit clockwise.
When standing facing the Suburban, the radiator drain plug is on the lower right-hand side of the radiator. Drain the radiator coolant into a bucket by turning the drain plug three-quarters of a turn to loosen.
Try leaving the belt on for tension on the pulley. Also you can very carefully use a pry bar to put extra tension on pulley while belt is on.
The power steering hose is secured with a swivel nut on each end of the hose. Loosen the swivel nuts by turning them to the left. The power steering hose will come off. Reverse the process to install the new power steering hose.
The 1997 Chevy Cavalier power steering hose is held in place with swivel nuts. Loosen the swivel nuts by turning them to the left. The power steering hose will come off. Reverse the process to install the new power steering hose.
The alternator is the adjustment point. Loosen the bolts holding the alternator to the engine and slide the alternator in towards the engine. This will allow you to remove the fan belt. However, if you also have power steering, the power steering belt may have to be removed before the alternator belt can be completely removed. Loosen the bolts holding the power steering pump assembly to the engine and slide the pump towards the engine to remove both belts.
Disconnect the battery. The starter should have two or three bolts holding it in. And there will be wires connected on it. Loosen the bolts and wiring connectors, then remove the starter from its mount.
Loosen cap on reservoir turn wheel lock-to-lock several times without holding in lock position.
Most have a lock to hold the shaft of the saw from turning and a nut holding the blade on. Hold the shaft, loosen the nut and remove the blade.
Get under the driver side of the suburban by the driver door and their should be a linkage that you can loosen
remove the center padded section on the steering wheel and you will see a large nut holding the wheel on, loosen the and take it off and then you will need a wheel puller to pull the wheel back off of the splines to take it off.
take horn cap off the center of the steering wheel and you will see large nut holding the wheel to the spindle, loosen nut and then you will need a wheel puller, install puller and tighten the nut down on the puller until the steering wheel frees itself from the spindle and your done.
On the four cylinder engine, all accessories are run with two belts, one for the power steering pump, the other drives the alternator and a/c compressor, etc. Loosen the bolts holding the power steering pump first. Please note the bolts that mount it are on the driver side of the engine, while the bolts that tension it, face the front of the car. Loosen (no need to remove) the tension bolt, remove the power steering belt. Loosen the bolts on the alternator, loosen the tension bolt on the alternator, push the alternator toward the engine and the belt is now free.
How does one change a power steering belt on a 1997 nissan pickup?
the chromatids holding the chromosome together loosen
No you have to loosen the lower ball joint take the spindle out of the lower control arm to pull the axle out. I was able to pull the axle thru the steering knuckle .After removing locking hub, rotor and spindle. (a slide hammer worked well for spindle)
If your Tercel has power steering, use a 14mm socket to loosen the two bolts that secure the power steering pump. Then turn the long jacking screw counterclockwise to loosen the serpentine belt.
If you have the key and it won't turn the lock cylinder try jiggling the steering wheel while turning the key. If the steering wheel lock is merely jammed that should loosen it enough to turn the key. On the other hand if you don't have the key or the lock itself is jammed you may want to replace the lock cylinder.
loosen the alternator bolts to get that belt off and the other belt is loosened by loosening the power steering reservoir bolts.
loosen the power steering pump pull that belt loosen the alt and remove belt and replace
Loosen the tensioner pulley. Remove the power steering belt. Remove the power steering hose. Remove the power steering retaining bolts. The power steering pump will come off.
To replace an Isuza Rodeo steering the steering column should first be removed. Pop off the front steering wheel cover to see the steering wheel nut. Loosen the nut and remove the wheel.
You have to loosen the power steering pump bolts and push down on the pump and the belt will loosen to take it off, to put it back on you route the belt over the pulleys and pull up on the steering pump and when tight tighten the pump bolts and your done.
Loosen the tensioner pulley. The power steering belt will come loose. Remove the power steering belt. Reverse the process to install the new power steering belt.
The shift knob should turn and loosen to the left. By turning this to the left it will loosen and come off, then put the new on and turning to the right until it's firm.