answersLogoWhite
Jeep Grand Cherokee
Jeep Grand Cherokee Laredo
Jeep Grand Cherokee Limited

How do you program a keyless transmitter on a 1998 5.9 Jeep Grand Cherokee?

121314

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 20:46:24
2015-07-15 20:46:24

According to the owner's manual that came with the car, page 15 says that the programming of the remote keyless entry, to stop the doors from automatically locking is to be done by the dealer. If you are trying to program the garage door opener in the visor to open the garage door, try reading the owner's manual, page 42-46. Very specific. be sure to follow the directions to a T. If all else fails the manual gives a telephone number for Homelink, the company that makes the system and suggests that you call their hotline. .

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions






I had the same problem. Google "keyless entry remote 2003 Jeep Grand Cherokee".


read the owner manual. It easy to reinitialize.


The answer can be found at: http://www.thejeep.com/pilandprogram.html



by pressing the lock button on the transmitter 5 times at intervals of two seconds until operational or by turning the ignition on run position until the chimes stop


This works for the 1993 Grand Cherokee: Sit inside the vehicle with all the doors closed. Place ignition in the OFF position. Open the driver's door. Leave Open. Move the mechanical door lever to the LOCK position. Turn the ignition to the RUN position. Aim the transmitter at the Keyless Entry receiver and press Lock button. Hold for five seconds until the door locks cycle. Turn ignition OFF within 20 seconds.


The keyless entry system must be programmed with an OBD II tool which the dealer or locksmith has. Sorry that this is not the answer your looking for, I didn't want to hear it either.


If it's the original transmitter and it has gone out of sync with the vehicle, hold down both the unlock and lock buttons until the car horn honks. This should re-sync. If it's a replacement transmitter, I think the dealer will have to program it.


This works for the Grand Cherokee:Sit inside the vehicle with all the doors closed. Place ignition in the OFF position.Open the driver's door. Leave Open.Move the mechanical door lever to the LOCK position.Turn the ignition to the RUN position.Aim the transmitter at the Keyless Entry receiver and press Lock button.Hold for five seconds until the door locks cycle.Turn ignition OFF within 20 seconds.


YOU CAN FINE ALMOST ANY KEYLESS ENTRY ON EBAY AND FOR A GOOD PRICE.. GOOD LUCK.........



THIS IS FOR A 93 BUT I WOULD THINK IT WOULD think it would also work on that 94.. programming 93 Jeep keyless fob This works for the 1993 Grand Cherokee: Sit inside the vehicle with all the doors closed. Place ignition in the OFF position. Open the driver's door. Leave Open. Move the mechanical door lever to the LOCK position. Turn the ignition to the RUN position. Aim the transmitter at the Keyless Entry receiver and press Lock button. Hold for five seconds until the door locks cycle. Turn ignition OFF within 20 seconds. good luck........


This is all I have on keyless entrys.I hope it helps. Sit inside the vehicle with all the doors closed. Place ignition in the OFF position. Open the driver's door. Leave Open. Move the mechanical door lever to the LOCK position. Turn the ignition to the RUN position. Aim the transmitter at the Keyless Entry receiver and press Lock button. Hold for five seconds until the door locks cycle. Turn ignition OFF within 20 seconds.


All After 1996 require the use of the Chrysler scan tool.


if you have only changed the batteries in your remote then you press the unlock button 6 times until you hear a beep and then it is programmed. these details are in the owners handbook.


this is all I got ..programming 93 Jeep keyless fobThis works for the Grand Cherokee:Sit inside the vehicle with all the doors closed.Place ignition in the OFF position.Open the driver's door. Leave Open.Move the mechanical door lever to the LOCK position.Turn the ignition to the RUN position.Aim the transmitter at the Keyless Entry receiver and press Lock button.Hold for five seconds until the door locks cycle.Turn ignition OFF within 20 seconds.



I am trying to find out how to do the reprogramming, but haven't found out how, but did find out that from 1999- 2004 the door lock fobs are interchangeable. You may need to take to Jeep dealer to actually get it programmed, but at least you won't have to buy a new fob.


how do you program a keyless entry remote to a 2000 Pontiac grandprix programyourremote.com (program your remote.com)


I had to replace a keyless remote for my 2001 dakota. I found one off od E-bay then I had to program it using the programing sequence in the owners manual. It was really simple. I only paid something like ten buck for the remote and have had no problems.




Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.