It should just pop off as far as i know.
2nd :
The front door has screws covered behind small caps. Use a small flat head screwdriver to remove them. This will expose the screws. The door has screws at the bottom and sides. Remove the srews (mark each screw as there are 3-4 different srews used on this door!!!)
Once all srews are removed, gently wiggle the door panel upwards.
Total time: 5-10 mins.
To remove the front door panel on a 1993 4Runner unscrew and pull off the mounting hardware, including the clips. The door panel will need just need to be pulled off.
Front door panel or rear? Either way there are screws on the very bottom of the panel, behind a tab in the handle (open door) recess, one in the handle you use to pull your door shut, one in each of three hole in the front middle when the door is open (front door). Take off the tweeter speaker. There might be a couple I missed, but study the door to find all screws and then you can pull the panel out a little then up. The lock tab, open handle, etc. are still connected so don't pull too hard.
the door panel can come off of your truck in less than 1 min. there are 2 screws on the panel. pull up on the front of your door switch panel and when it pops up move it towards the front of the truck there will be one bolt there and the pry the light cover off at the door panel and there will be another bolt there i think they are 7mm bolts. you will also have to pull the black trim off at the top front of the panel, just pull staight out. then roll down the windoe and lift the door panel strait up, and the door panal is off. easiest door panel evrer to come off. hope this helps. really it is very, very easy.
Use a screw driver, remove the screws and the clips in the door panel of the car. Gently pull the panel away from the door, disconnect the wire connections between the panel and the door, and remove the panel the rest of the way.
Can you get inside the car and remove the interior panel of the door that is stuck ? If you can remove that panel you will be able to manually pull the door catch (And then open the door and have the door latch fixed properly)
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
You don't have to pull the door panel off... the speaker grille snaps in place. Use a small screwdriver to carefully pry the grille from the panel
Which panel are you in reference to? The kick panel or the door panel? If it's the kick panel there is a plastic rivot you need to pull out loctated on the forward portion, then you will need to remove the lower plastic from the floorboard that lines the door opening, then you will be able to pull the panel towards the door opening and it will pop right out.
pop out the door handle cup behind there is a screw remove it,Now on the front of the door panel around the edge were the panel meets the door frame,Theres a lil black clip,Pull it out then you lift straight up and the panel comes off.
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors