0
How do you remove 1988 jeep Cherokee door panel with window crank?
Wiki User
∙ 15y ago
Pull the window crank. It just snaps on and off. Remove two philipps head screws from the arm rest. Tilt the arm rest up about 90 degrees or so and the top part of it will pull out from the door. Remove three phlilps head screws from the door latch handle/ door lock plate. Slide it forward. Do not remove the rods to the ltch handle or door lock(you can get it off with out removing them. Pull the door panel out starting with the bottom. I has 12 or so push in plastic locks. BE VERY CAREFUL not to rip them out of the door panel. Now its time to just gently twist the latch/lock plate throught the panel and remove it.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Can you unbolt a window motor out of a 1997 jeep Cherokee door and bolt in manual crank?
You would need to remove the window regulator, and the motor. Replace them both and drill a hold through your door panel where the crank will come out.
How do you replace the window crank on a Chevy lumina 1997?
Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
How do you replace the rear window crank on 77 blazer?
You will need to remove the inside door panel of your 1977 Chevrolet blazer. Remove the window crank linkage. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
How do you remove the door panel of a 2001 Sonoma does not have power windows?
You need to remove the window hand crank with a window hand crank removal tool.
How do you remove quarter windows from a 56 Chevy?
You have to remove the inside panel, where the window crank is, or would be.
How do you replace the window crank handle on a 93 Geo Prism?
To replace the window crank handle on the 1993 Geo Prism, first remove the interior door panel. Then, access the screw that holds the window crank in place and remove it. You can then remove the handle itself.
How do you remove a door panel on a 1984 Mercedes 300d?
you have to remove window crank and door handel first
How do you remove the window crank on a 1992 Toyota Paseo?
To remove the window crank on the 1992 Toyota Paseo, first pry off the interior door panel. Then, access the screw that holds the crank in place. Remove the screw and the handle will come loose.
How do you remove door window from 1968 Chevy Truck C20?
Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.
How do you remove the the window crank from the inside door panel of a 1993 Honda Accord LS?
you need to remove the inner door panel. Usually pop grommets but may be screwed. That will give you acess to the crank and the inner workings of the door to remove and connect a power window if needed.
How to remove a window handle on a 1997 Firebird?
You can remove the window crank handle by just using a simple shop rag. How you do this you slide the rag(unfolded) between the door panel and window crank and rotate around the window crank until you snag the clip that is retain the window crank. The clip is a simple wire clip shaped like a "C" To reinstall you place the clip back in the groove on window crank and press back on the window regualtor shaft
How do you remove the interior door panel from a 1993 Chevy Silverado?
General Chevy info, remove door hande bezel, remove armrest, remove window crank if it has manual windows.(there is a clip on the crank) Start at the bottom and gently pry panel up pulling plasic clips out of holes in door. When panel is loose it will lift off of window ledge. If you have power windows or locks you will have to unplug the switches carefully
