answersLogoWhite

0


Best Answer

it's 2 screws located where the leather pull handle meet the door panel. remove those and the rest is just pull clips located behind the door panel.once you done that you got access to 1 bolt that holds that side mirrow.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove a 1998 Town Car door panel to replace the side mirror?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace a passenger side mirror on a 1998 jimmy?

you have to remove door panel and there are three nuts you have to take off of the mirror.


How do you replace Side mirror on a 1998 sls cadillac?

remove the door panel screws and pull up on the door panel to correctly remove it. then remove the 3 bolts on the upper corner and unplug and replace


How do you replace a side view mirror on a 1998 Mazda Millennia mirror only?

remove corner trim it pops off remove door panel screw in compartmnet on edge and by handle unplug remove three screws and replace


How do you replace a passenger side mirror on a 1998 Nissan maxima SE electric non heated?

To replace the passenger side mirror on the 1998 Nissan Maxima SE, first remove the door panel inside the door by releasing the clips below the panel and by unscrewing the handle screws. Then, remove the trim panel that covers the mirror mount inside the vehicle. There should be at least 4 screws. Release the wires from the old mirror and take the part off of the car. Add the new mirror and connect the wires. Replace the screws and the door panel.


How do you replace the driver side view mirror on a 1998 ford expedition?

Remove the front door sail panel. There you will see 3 bolts holding the side view mirror. Remove bolts, replace / or fix side view mirror. Installation is the reverse of removal.


How do you replace the manual drivers side mirror on a 1998 Hombre?

On the 1996 Hombre, you have to remove the inside door panel. You will see three nuts holding the mirror. Try Advance Auto Parts for replacement mirror (probably same as S-10).


How do you replace the passengers side mirror on a 1998 Ford Expedition?

Remove the plastic cover on the inside behind the mirror and then remove the three nuts holding ther mirror on. When you pull out the mirror unclip the wiring harness.


How do you replace the dash speakers in a 1998 Chrysler Cirrus?

Remove center stack bezel (radio, heater control), remove screws from instrument trim panel at ctr stack and remove instrument trim panel, remove dash top panel, replace speakers.


Instructions on how to replace drivers side power mirror on 1998 GMC Jimmy?

Remove the inside door panel. Should be 3 screws total, 2 on door close handle, 1 by opener/lock panel. If you have non-power windows remove the window crank. Pull on door panel to release the plastic grommets holding the panel to the door. Then pull the panel up off the window track. If power windows undo the power cable. Once the panel is off, up where the mirror is there should be 3 rubber type stoppers in the door, this is for sound reduction, remove those. Inside the holes are the nuts holding the mirror. Remove the nuts, careful to not lose any, pull the mirror out from the outside, remove power cable. Install new mirror, and replace everything else in reverse order. DON'T OVER TIGHTEN THE NUTS. I did this to one and snapped it off the plastic of the mirror. Replaced a 1997 Blazer mirror, good luck!


How do you remove the driver side door panel of a 1999 Beetle to replace door lock?

How do you remove the driver side door panel of a 1998 VW Beetle to replace the door handle cable?


How do you replace the side view mirror on a 1998 Pontiac Bonneville?

You have to take the door panel off on the inside of the door, and there are two bolts that hold the mirror housing. Its a real pain in the neck. If your just trying to take the mirror out of the housing and replace it, sorry I can't help you there.


How do you remove a Driver side mirror from a 1998 Chevy Blazer?

You need to remove the inside panel, where the arm rest and the control switches are. 2 screws under the arm rest then the pannel is held by snap in pins. After removing the inside panel, you will have access to 3 screws holding the mirror, this applies to the passenger side too. You may need to buy new snap in pins from Strauss or Autozone to replace the old ones that get damage when removing the panel.