How do you remove front bumper cover on 2000 impala?
- Park the Impala on a level surface and engage the parking brake. Remove the keys from the vehicle's ignition.
Crawl underneath the front of the vehicle and use a slotted screwdriver to pry off the splash shield in each wheel well directly in front of both front tires. Once the shields are removed, you can access the screws securing the bumper cover to the fender.
Remove the two screws on each side of the bumper cover with a Phillips screwdriver.
Remove the bumper cover from the front of the vehicle by pulling it up and off the Impala. You may need another person to help you remove the bumper cover. Install a new bumper cover by placing it onto the front of the Impala.
Crawl underneath the Impala again and reinstall the two screws on each side of the bumper cover. Reattach the splash shields to the wheel wells.
Unbolt the front of the wheel well liner inside the wheel opening. Remove the bumper cover bolt from the bracket located inside of the bumper at the end. AT the front of the car, remove the bolts holding the bumper cover on, located underneath the vehicle. You should now be able to remove the bumper cover from the front of your Dodge Intrepid. An instructional video has been included to show you the removal process.
Not Necessary but helps a lot: Jack the front of the car up on both sides and remove the front wheels. Remove the bolts that hold the plastic fender well up. If you look at the seam where the front bumper cover meets the right front corner panel (one's metal and one's plastic) there are more bolts to remove. Pop the hood, and remove the push locks that hold the plastic bumper to the metal…
# Apply parking brake,raise the vehicle and secure it # working under the vehicle,detach the fasteners securing the lower edges of the bumper cover # Working in the front wheel opening,detach the retaining screws securring the bumper cover to the inner fenderwell splash shield # Pry out the lower edge of the splash shield,then reach up behind the bumper cover and remove the bumper cover fender retaining nuts # remove the fasteners securing the upper…
1. Remove the two bolts underneath the ends of the front bumper with a socket wrench. 2. Unfasten the six clips underneath the front bumper along the center with a screwdriver. 3. Remove the two clips on the top of the front bumper next to the radiator, using a screwdriver. 4. Unfasten the screw that secures the front bumper to each fenderwell, using a screwdriver. The fenderwells are the void areas where the front tires…
To remove the front bumper from a Celebrity: 1. Raise the vehicle as needed and put on stands. The parking brake should be on. 2. Remove the end covers 3. Remove the valence cover. 4. Remove the nuts that hold the bumper to the mounting struts. Be careful to avoid having the bumper fall off onto you. 5. Remove the bumper. Reverse these instructions to put the bumper back on.
there are 6 10mm bolts that hold the bumper. you will have to remove your mudcover. then there are 6 bolts on the inside of the bumper (3 on each side by the wheel) and 2 pins that hold it (by the hood release) these you pry of with a flat screwdriver. after removing these you should be able to remove the bumper
Pull your liner down at the front points of rear bumper and remove the two #10 bolts....take visable bolts and clips off the bottom of cover....lift gate---open storage compartment---remove plastic clips that hold liner and remove liner---remove two black clips that hold trim plate and remove trim plate---there will be 5 #10 bolts inside holes in to remove .....pull cover off! Note: from front points of cover to gate the cover just snaps in.
To remove the front bumper on a zx2 , first you need to remove all of the fasteners on the top side of the bumper. ( open the hood and look straight down, remove all of those black plastic retaing screws.) After you remove the fasteners from the topyou need to lay down and get all of those small screws on the bottom/front of the bumper. Basically they just hold on the front splash guard…
* Apply the parking brake raise the vehicle and support it securely on jackstands * Disconnect the negative battery cable and disconnect any wiring that would interfere with bumper removal * From below remove the splash panel below the radiator and bumper * Remove the radiator grille and remove the headlight housings,turn signal lamps and cornering lamps * Remove the headlights and cornering lamps and remove the fasica to fender fasteners then remove the remaining…
To replace a Pontiac Grand Am bumper cover, start by taking out either the three bolts on the side of the fender or in front of the wheels. Remove the top pushpins to remove the cover. Push back the two pins for each headlight, and pull them up. Unplug the lights. Then, get the replacement bumper, and snap it into place like the previous one.
Remove the fuse block from behind the passenger\'s side headlight. Remove the battery from behind the driver side headlight. Next you will need to remove the bumper cover. Remove the two 10MM bolts from the top of the cover between the headlights. Pry the clip in the middle up with a screwdriver. It\'s right in front of the hood latch. There are two bolts on the bumper cover ends at the wheel opening that need…
The headlight is fastened by three bolts. The top one is obvious and is on top of the slam panel. The other two are behind the bumper, under the headlight. To get at them you have to partially remove the bumper cover. Remove the plastic plugs holding the front part of the wheel arch cover. Undo three cross head screws securing the cover to the bumper underneath. Remove three 10mm bolts holding the bottom of…
1. apply the parking brake, block rear wheels, jack up front end and place on jack stands2. disconect negative battery cable3.detatch air duct from bumper cover (ac models)4.remove side markers and headlamp assemblies5.remove bumper cover nuts, bolts, and clips6.disconect any electrical connectors that would interfere7.remove the rivets and retainers and pull the absorber and bumper assemblies
These jeeps have a metal plate, and then a rubber bumper cover is bolted onto the plate. There are two bolts on either side of the bumper cover (on the inside of the bumper cover). Taking the cover off requires a ratchet. Taking the plate off requires a bit more work, as there are more bolts to contend with, as well as the skid plate, etc.
First remove the bumper under tray, then remove the front of both front inner wheel liners. Then there is one 10mm bolt on both lh and rh sides behind the bumper above both front merker lights. Then remove the two 10mm bolts above both headlamp assemblies, and don't forget to remove the bumper slowly so that you can disconnect the bumper harness.
To remove the front bumper * Remove the front indicators * Raise the front wheels off the ground and support the front of the car with axle stands * Looking under the front of the car you will see a cross-member which supports the front of the engine and the radiator etc. You should see the heads of three bolts at each end of the cross-member. The outer two bolts are the ones securing the…