Auto Parts and Repairs
Plymouth Voyager
VW Jetta
Ford Expedition XLT

How do you remove the back hubs from a 1989 Plymouth Voyager?

383940

Top Answer
User Avatar
Wiki User
2015-07-15 19:37:02
2015-07-15 19:37:02

remove the wheels, then the drums and brake sfoes. There are 4 bolts that hold the hubs onto the axel. Make sure to replace the shims if present when replacing it.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

When you want drop a lot of heavy loads and need to pull it out, just yank it out.

User Avatar

You reach over the top, or Jack the van up and reach them from underneath.

User Avatar

My 1998 PLYMOUTH GRAND VOYAGER has 2 pumps one for the front and one for the back. They are both located in the bottom of the reservoir.

User Avatar

To remove the headrest on a 1994 Plymouth Voyager Van, push the headrest all the way down. Then gently push the headrest back and pull straight up. Some seat models also have a lever on the side of the seat to depress to remove the headrest.

User Avatar

It is in the exhaust manifold on the back of the engine.

User Avatar

under the hod driver side back with the firewall

User Avatar

Pull the cup holder out. Reach back, and at the top rear, center-left, is a tab. Press the tab down and pull out on the cup holder to remove it.

User Avatar

Remove the item from the back which is preventing it from closing. Let's face it, you need to describe a little better why it isn't closing if you want a real answer

User Avatar

There are 2 latches. usually black, behind the seat on each side. Press them down then lift the back up first. Once you get the back up you can slide the seat back a little to release the front of the latches.

User Avatar

try the brake switch on the back of the brake pedal

User Avatar

It is on the back side of the under dash fuse box.

User Avatar

It is on the back side of the under dash fuse panel.

User Avatar

Yes it is on passenger side on back side of the intake manifold

User Avatar

Remove tire. Remove Caliper and pads The Rotor will just slip right off the spindle... Put new rotor on, put caliper plus pads back and the tire and your done, its really simple to do.

User Avatar

It is on the passenger side "frame rail" about half way from the front to the back.

User Avatar

unscrew it then pull it out put in the new one screw it back in retard

User Avatar

It is on the back side of the under dash fuse box.

User Avatar

It is on the inside of the passenger side "frame" rail, about half way from the front to back.

User Avatar

1 3 5 Back 2 4 6 Front (facing your engine)

User Avatar

They are the same, as far as I know. Plymouth was a marque of the Chrysler Corporation that they discontinued around the turn of the century. The Plymouth Voyager was the equivalent of the Dodge Caravan, a minivan on a smaller chassis than the similar Dodge Grand Caravan and Chrysler Town and Country; prior to the end of Plymouth, Chrysler did not have an equivalent, so they moved the Voyager over from the Plymouth model line to Chrysler's. This is the story I got from a Chrysler salesman back in 2001, when I noticed the same thing. Chrysler also uses the name "Voyager" for the minivans that they sell in Europe; (rather than "Town & Country" as in the U.S.)

User Avatar

It is on the back side of the under dash fuse panel on the driver side of the dash.

User Avatar

1995 Plymouth Voyager will crank up, but when you shift it in gear, it cuts off

User Avatar

your horns driver side in the front wheel well in the back cover wheel look up

User Avatar

To remove the back seat on a 1989 Ford Thunderbird, the first step is to remove the back of the seat. The back is held in by bolts on each side. After the back is removed, the seat area should come out after removing the floor bolts.

User Avatar

Follow the upper radiator hose to the engine... that is where its located inside the thermostat housing. Remove upper hose to the engine, then remove the 2 bolts holding the thermostat housing on, then remove thermostat, replace with new one plus gasket, put the housing back on, hose back on, refill with all fluids lost and your done. really simple.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.