Heater Cores and Blower Fans
Oldsmobile Ciera

How do you remove the blower motor and fan on a 1990 Cutlass Ciera?

626364

Top Answer
User Avatar
Wiki User
2006-08-17 02:54:29
2006-08-17 02:54:29
The radiator fan motor is conected to the shroud by 4 -10 mm screws. remove them and lower fan motor bracket down to allow access to the electrical connection from the motor it is a press fit with a latch. With electrical disconnected lift up and out of the engine compartment. After it is out there are three screws holding motor to bracket. The fan blade is attached by one nut -left hand thread.
1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the wiring harness from the back of your 1995 Oldsmobile Cutlass blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install your new blower motor.

User Avatar

It's on the firewall up high on the passenger side. You may need to remove the alternator to get it out.

User Avatar

unplug the blower motor (electrical) Unbolt the blower moter Remove the alternator Remove the top powersteering bracket bolt Loosen the lower powersteering bolt Pry the powersteering pump towards the front of the car as much as possible Have a freind pry the engine towards the front of the car while you rotate and turn the blower motor out of the housing. Caution do not bend the fins on the blower motor. Its a tight fit but will come out with the right angle

User Avatar

Remove the blower motor retaining nuts. Remove the wiring harness from the back of the blower motor. Remove the fan from the blower motor. Reverse the process to install the new blower motor.

User Avatar

Remove the wiring harness from the back of the blower motor. Remove the fan from the front of the blower motor. Remove the blower motor retaining nuts. Reverse the process to install the new blower motor

User Avatar

Remove the wiring harness from the back of the blower motor. Remove the blower motor retaining screws. Remove the fan from the blower motor. Reverse the process to install the new blower motor.

User Avatar

Remove the wiring harness from the 1996 Chevy Cavalier blower motor. Remove the blower motor retaining bolts. Remove the blower motor fan. Reverse the process to install the new blower motor.

User Avatar

Remove the wiring harness from the back of your 2001 Chevrolet Corvette blower motor. Remove the blower motor retaining bolts. Remove the blower motor fan. Reverse the process to install the new blower motor.

User Avatar

Remove the wiring harness from the back of your 1996 Chevrolet blower motor. Remove the blower motor retaining bolts. Remove the fan from the blower motor. Reverse the process to install your new blower motor.

User Avatar

Remove the wiring harness from the back of your 1993 Chevrolet Camaro blower motor. Remove the blower motor retaining nuts. Remove the fan from the front of the blower motor. Reverse the process to install the new blower motor.

User Avatar

The Oldsmobile Cutlass Cierra window lift motor is located inside of the door. Each window is equipped with a window lift motor.

User Avatar

The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.

User Avatar

Remove the wiring harness from the back of your 1995 Oldsmobile Aurora blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install your new blower motor.

User Avatar

Remove the wiring harness from the back of your 1996 Chevy Corsica blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install the new blower motor.

User Avatar

the blower fan motor is located under the passenger side dash, just remove the panel and then unbolt everything in your way until you come to a sort of triangular shaped blower motor.

User Avatar

Blower motor: remove the glove box and you will see the blower motor and blower resistor.

User Avatar

Remove the wiring harness from the back of the blower motor in your 1993 GMC 1500. Remove the blower motor retaining bolts. If the new blower motor does not have the fan attached to and you will need to remove the fan from the old blower motor. Reverse the process to install the new blower motor.

User Avatar

Remove monoblade. Remove bezel. Remove monoblade motor. Remove blower motor cover. Remove remove motor clip. Remove power connection.

User Avatar

Remove the wiring harness from the back of your 1980 Chevy Camaro heater blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install the new blower motor.

User Avatar

Remove the wiring harness from the back of your 1999 Chevy Monte Carlo blower motor. Remove the blower motor retaining bolts. Remove the fan on the front of the blower motor. Reverse the process to install the new blower motor.

User Avatar

Remove the wiring harness from the back of your 1986 Lincoln air conditioning blower motor. Remove the blower motor retaining bolts. Remove the fan on the front of the blower motor. Reverse the process to install the new blower motor.

User Avatar

Begin by removing the wiring harness from the back of your blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install your new blower motor.

User Avatar

Remove the instrument panel silencer from the passenger side of the instrument panel. Disconnect the wire harness connector from the blower motor. Remove the three screws that secure the blower motor to the HVAC housing. Remove the blower motor from the HVAC housing by rotating and tilting the motor as needed for clearance of the blower wheel....

User Avatar

Remove the front floor kick-up panel.Remove the cover from the I/P electrical center.Remove the BLO MOT (blower motor) MaxiFuse No. 49 from the I/P electrical center.Remove the right side instrument panel lower insulator panel.Disconnect the blower motor resistor electrical connector from the blower motor.Disconnect the blower motor cooling tube from the HVAC module.Remove the three blower motor retaining screws.Remove the blower motor with fan from the HVAC module.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.